Скачать с ютуб 1996 - 2000 Toyota Rav4 EGR VSV, Vacuum Switching Valve for EGR, Remove, Replace, Bench Test, P0401 в хорошем качестве

1996 - 2000 Toyota Rav4 EGR VSV, Vacuum Switching Valve for EGR, Remove, Replace, Bench Test, P0401

This video shows how to remove the VSV (VSV for EGR) on the '96 - '00 Rav4. The VSV is in a hard to reach place: you can just disconnect the blue electrical connector and the two hoses and leave your old VSV where it is if you can't reach the bolt. You can then mount your new VSV in a different location on the firewall which is easier to reach. This videos shows how to remove the VSV and how to mount it to the new location. Links for the EGR Diagnostics and EGR Valve and Pipe removal videos are below the Timestamps: 00:15 Part numbers for VSV 00:35 In place testing of the VSV and explanation of function 02:42 Key OFF test for VSV 05:06 Key ON test for VSV 09:05 Start process for VSV removal (shown on 4WD Rav4) 09:14 Locate the VSV using the vacuum hoses 09:50 Recommended to remove passenger side tire on 4WD for better access 10:00 Finding the VSV (look for blue electrical connector) 10:20 Disconnect blue electrical connector 11:12 Decide if you'll just leave old VSV in place, or try to remove it. If you're leaving the only VSV in place, skip ahead to 20:30 to see the hose removal and then bench testing. If you're removing the old VSV: 12:45 Remove transfer case dipstick 13:00 Disconnect tie rod end for more access if needed 14:56 Remove 12mm mounting bolt (firstly trying a little Gearwrench mini #85035, but failing) 16:30 Next trying a ratchet and failing again 17:33 Fitting an air ratchet in this tight space, air ratchet did the trick 19:57 Air ratchet and extension setup 20:29 Remove hoses from VSV 20:51 Remove hose bracket bolt 21:39 Disconnect hoses from Vacuum Modulator and EGR Valve 23:12 Bench testing the VSV 23:29 Resistance Tests 24:54 Flow Test 25:22 Switching Test 26:50 Test for leaks 28:43 VSV part numbers (Toyota #90910-12100 or Aisin VST-034) 29:06 Install VSV to new location on firewall (bolt is M6 x 1.00, about 15 mm long) 29:45 Remove battery and tray for better access 30:29 Bend tap on VSV bracket for better fit 30:42 Move blue electrical connector over towards firewall 31:33 If you have ABS, remove the 10mm bolt on the brake line bracket 31:47 Mount VSV in new location 32:15 Position and connect hoses to VSV 34:55 Modify hose bracket for better fit 36:37 VSV in place, in new location 38:07 Reinstall battery tray and battery 39:22 Reinstall 10mm bolt on back of engine and other bolts under engine 40:36 Replace transfer case dipstick 40:40 Reconnect tie rod end (17mm castle nut torque is 36 ft-lbs) and wheel (lug nuts: 76 ft-lbs) 41:36 Final check on hose and electrical EGR Diagnostics video with explanation, in-engine, and bench testing of EGR valve, Vacuum Modulator, and VSV:    • 1996 - 2000 Rav4 EGR Diagnosis, Engin...   Video for removing the EGR Valve and pipe (and IAC Valve and Throttle Body):    • 1996 - 2000 Toyota Rav4 DIY Remove Th...   Thanks for watching! I hope this was helpful for you. Good luck with your repair!