У нас вы можете посмотреть бесплатно ACI Density Test: ASTM C138 Density (Unit Weight) 2019 или скачать в максимальном доступном качестве, которое было загружено на ютуб. Для скачивания выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса savevideohd.ru
Density (Unit Weight) ACI Technician Workbook CP-1 ------------------------------------------------------------------ Density * To figure out the density, you are filling up a container with concrete. This container must have a known volume (4), minimum .20 cubic feet. First weigh the empty container (1) and record that value to the nearest tenth (.1) of a pound. After performing the proper procedures for filling the container (i.e. filling it in three lifts, mallet blows, rodding, striking off with strike-off plate), follow these steps: Density Calculation Steps * Weigh the container with the concrete (2) - record value to nearest tenth of a pound Subtract the empty container weight from the full container weight (2) - (1) = weight of concrete (3) Divide the weight of concrete by the known volume (3) / (4) = density, or fresh unit weight There’s a few unique procedures listed in the ASTM C138 to remember: Slump * If less than 1": Must use vibrator capable of at least 9,000 vibrations per minute If between 1" and 3": use vibrator or tamping rod If greater than 3" = Can’t use vibrator, only use tamping rod If using vibrator, fill and vibrate measure in two equal layers, not three Insert vibrator at three different points for each layer approx. 3 inches into the underlying layer Mallet mass must be 1.25 +- .5 lb for containers .5 cu.ft. or smaller Mallet mass 2.25 +- .5 lb for containers larger than .5 cu.ft. Use strike-off plate, not bar Metal strike-off plate dimensions - 1/4" thick Glass or acrylic plate dimensions - 1/2" thick Yield * Yield is used to determine if the concrete supplier has delivered the amount of concrete ordered. For example, if the contractor orders 7 yards and the concrete pour comes short of filling the structure, a yield test can be performed to determine if 7 yards were actually delivered. To calculate yield, follow these simple steps. Note that you must calculate density prior to calculating yield. You will take the total mass of all materials batched (aggregate, water, cement–this figure will be given to you on the test) to begin. The total mass of the materials is the total weight. a. The yield per batch cu.ft.Total weight / fresh unit weight = yield per batch in feet b. The yield per batch in cu.yds.Total weight / (fresh unit weight x 27) = yield per batch in yards c. The yield in cu.m.Yield per batch in cu.yards x .764 = yield in cu.meters (1 cu. yd. = .764 cu. meters. This will not be on the test.) d. The yield per cubic yard in cu.ft./cu.yd.Yield per batch [result from (a)] / cu.yds delivered = yield per cu.yd. in cu.ft./cu.yd. RELATIVE YIELD is the ratio of the actual volume of concrete obtained to the volume as designed for the batch. It is understood as a 1:1 ratio. If the relative yield calculates out to 1.00 or greater, then the yards delivered is equal to or greater than what was ordered. If it calculates to less than 1.00, then the yards delivered is less than what was ordered. RELATIVE YIELD = yield per batch in yards (b) / cu. yds. delivered Air Content Calculation * Air content can be calculated in the event that your air meter does not work properly. In order to calculate this, you must have the theoretical density. This information can be obtained from the concrete supplier, who has this information on the mix design for the mix you are working with. Again, you will need your results from the fresh unit weight. THEORETICAL DENSITY = actual density (fresh unit weight) / theoretical x 100 = calculated air content Since the theoretical density from the lab has no air, you are comparing that laboratory weight to the fresh weight which contains air. The air in the fresh weight sample makes it lighter than the theoretical. The formula above allows you to subtract the fresh from the theoretical and come up with a calculated percentage of air content without performing an actual test. For the ACI test, all that is necessary is to be able to recognize the order of the formula written above. ------------------------------------------------------------------ Want to pass a special inspection exam? Enroll in an online ICC course today: https://sicerts.com/courses