⛑️VANMOOF S3/X3 NOT CHARGING ERROR 19/21 Charger Plug loose , how to fix ? скачать в хорошем качестве

⛑️VANMOOF S3/X3 NOT CHARGING ERROR 19/21 Charger Plug loose , how to fix ?

Hello guys thanks for watching.. Also I'm trying to make a channel regarding problems like this if you have any suggestions or challenges for me I'm happy to try solving them :) if u need get in touch please do so on razspareparts@gmail.com don't hesitate to contact Razspareparts UK this is the full list of errors to your S3/X3 Bike 🚲 Here are the battery-related errors for the VanMoof S3: 1. BAT SCP: Short circuit protection (main battery related) 2. BAT_ MOTP: Mosfet over temperature protection (main battery related) 3. BAT_PDSCP: Pre discharge short circuit protection (main battery related) 4.BAT_PDOCP: Pre discharge overload circuit protection (main battery related) 5. BAT_UVP2: Under voltage protection 2 (main battery related) (try charging for a longer period, could solve issue) 6. BAT_UVP1: Under voltage protection 1 (main battery related) 7. BAT_ OVP2: Over voltage protection 2 (main battery related) 8. BAT_OVP1: Over voltage protection 1 (main battery 8. BAT_OVP1: Over voltage protection 1 (main battery related) 9. BAT_COCP1: Charge over current protection 1 (main battery related) 10. BAT COCP2: Charge over current protection 2 (main battery related) 11. BAT DOCP2: Discharge Over current protection 2 (main battery related) 12. BAT DOCP1: Discharge Over curent protection 1 (main battery related) 13. BAT_CUTP: Charge under temperature protection (main battery related) (it's too cold to charge) 14. BAT COTP: Charge over temperature protection (main battery related) (it's too warm to charge) 15. BAT DUTP: Discharge under temperature protection (main battery related) (it's too cold to discharge) 16. BAT DOTP: Discharge over temperature protection (main battery related) (it's too hot to discharge) 17. BATFP: Permnanent fail (fuse burn) (main battery related) (likely socket short circuit) 18. Error 17: BATTERY_ NO_DSG - Could not set discharge mode (main battery related) 19. Error 18: BATTERY_MISSING - Signal bat_key_in is low (main battery related) (battery not recognized, also the error you get when no battery is present) 20. Error 19: BATTERY COMMUNICATION Modbus battery (main battery related) 21. Error 20: BMS seems to shutdown (main battery related) 22. Error 21: NO_ CHARGE_CURRENT Charging state but no current reported (main battery related) 23. Error22 SSP TI Motor chip (module related) 24. Error 23: BLE chip (module related) (Bluetooth chip) 25. Error 24: OAD _ABORT Transfer from app aborted (Module related) (Upload was aborted?) 26. Error 25: OAD_ CRC - Transferred image crc error (Module related) 27. Error 26: OAD file transfer took too long (Module related) 28. Error 27: OAD_PACK - No or invalid file in pack (Module related) 29. Error 28: ICF_TIMEOUT - Timeout during flash programming (Module related) HEADER - 30. Error 29: ICF Header not found (Module related) 31. Error 30: \CF_ NO_FILES - No files in pack (Module related) 32. Error 31: ICF ERASE - Flash erase error (Module related) 33. Error 32: ICF WRITE - Flash write error (Module related) 34. Error 33: ICF CRC - File in pack has CRC error (Module related) 35. Error 34 - Programming of the motor Controller failed 36. Error 35: PGM_BATTERYWARE - Programming of the BMS Controller failed 37. Error 36: PGM_SHIFTERWARE - Programming of the shifter Controller failed 38. Error 37: PGM_BLEWARE - Programming of the BLE Controller failed 39. Error 38: - STVC3115 read error, LiPo might be missing (Module related) (check if battery m o io hor) 40. Error 39: READ_LIGHT _SENSOR CM3232 12C read u - Kick- Lock coil not detected 44. Error 43: SHIFTER_NOT_IN_GEAR - After 10 tries, gear has not been reached 45. Error 44: SHIFTER COMMUNICATION - Modbus Shifter (Shifter not recognized) (Plug in tester Shifter) 46. Error 45: MOTOR MOTOR CABLE - Bit2/NTC motor cable not Connected (Motor not recognized) 47. Error 46: MOTOR MOTOR_OVER CURRENT DRV8301 over temperature (bit6) 48. Error 48: MOTOR CONTROLLER_ERROR Error in user parameters (bit8) (replace motor) 49. Error 49: MOTOR CURRENT_ERR - Current offset calculation +- from default value 1.0 50. Error 50: MOTOR_VOLTAGE_ERR - Voltage offset calculation +*from Vbat/2 or Vbat 51. Error 51: MOTOR_ DERATING - Max current limited due to high temp 52. Error 52: MOTOR TORQUE_SENSOR FAIL Torque sensor failed, only if sensor required 53. Error 53: MOTOR NOT READY - Motor not ready during motor test or error 54. Error 54: NO SIMCARD - SIM card not present (Module related) (SIM not recognized) 55. Error 55: 12C3_FAIL - Started with l2C error on bus 3 56. Error 56: CCID_SIMCARD - SIM card wrong CCID (VanMoof) number 57. Error 57: READ_SIMCARD - SIM card is detected but no communication (Module related) (Check ICCD number in BO) 58. Error 58: GSM_MODEM - Modem startup sequence failed (Module related) (often gone after reset) 60. Error 60: FACTORY_MODE Display 60 when factory hope it helps ☺️