У нас вы можете посмотреть бесплатно How to Manual Swap an Automatic Toyota MR2 SW20 (1991-1995) | Part 3 of 3 или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса ClipSaver.ru
This is part 3 of a three-part guide on how to manual swap an automatic 1991-1995 Toyota MR2 SW20. My 1991 Toyota MR2 is equipped with the 5S-FE engine and had the A241E automatic transmission but now after doing the swap it has an S54 transmission off of a 91 non-turbo Toyota MR2. In this video I go over the remaining items that I had left to complete the manual swap. The chapters below will show all that remained to complete the manual swap. I'd like to note that I already had the automatic transmission removed due to removing the engine and transmission to perform a refresh on my engine. You don't have to remove the engine and transmission together to remove the transmission, you can leave the engine supported with an engine support bar and remove the transmission by itself. If you'd like to remove the engine and transmission together to perform work on your engine like I did, I'll link my videos down below on how to remove them. The videos could also serve as a guide even if you're just removing the transmission by itself so feel free to check them out. Step-by-Step Guide: How to Remove the Engine & Transmission from a 1991-1995 Toyota MR2 (Part 1/2) • Step-by-Step Guide: How to Remove the Engi... Step-by-Step Guide: How to Remove the Engine & Transmission from a 1991-1995 Toyota MR2 (Part 2/2) • Step-by-Step Guide: How to Remove the Engi... Parts list - (the parts listed below are the parts that were mentioned in this video, due to the limitation of 5000 characters in a YouTube description the rest of the parts needed for the swap will be in the description of part 1 and 2.) S54 manual transmission Flywheel I used - Perfection Clutch 50108 Flywheel bolts - 90105-10071 (x8) Clutch kit I used - Aisin CKT-027 (includes clutch, pressure plate, throw out bearing, and clutch alignment tool) Pressure plate bolts - 90119-08026 (x6) Input shaft seal - 90311-30017 Cv axle seals - 90311-35019 (x2) Left cv axle seal plate o ring - 90301-63004 (discontinued) Speedometer shaft sleeve o ring - 96711-24018 Transmission bellhousing bolts x 3 - 90119-12168 Clutch slave cylinder - Aisin CRT031 for 91 s54 transmission or Aisin CRT090 for S54 transmissions from 02/1992 and onwards Clutch slave cylinder bracket with clutch lines - get used Retainer that holds clutch lines on clutch slave cylinder bracket down - 31468-17010 Bolt that holds retainer for clutch lines on clutch slave cylinder bracket - 91651-60818 Left transmission mount bracket - 12325-74120 (discontinued) so get used or make sure transmission comes with one Left transmission mount - 12372-74280 Rear transmission mount bracket - 12321-74190 (discontinued) so get used or make sure transmission comes with one Front transmission mount - 12361-74160 (you can technically use the automatic one since they appear the same however the part number does change, I replaced mine with one from rock auto) DEA / Marmon Ride control front mount I used - A62001 Shifter cables clips - 90468-14016 (x2) (reuse the 2 from the automatic shifter cable and get 2 more for the manual ones to have 4 in total) Shifter cable washers - 90201-08267 (x3) Shifter cable clip to hold washer and cable in place - 90468-14017 (reuse the 1 from the automatic shifter cable and get 1 more for the manual ones to have 2 in total) Clutch hose - 90947-02611 Dot 3 brake fluid 75w90 gear oil (3 quarts) - I used Redline MT90 Drain and refill plug washers - 90430-18008 (x2) Back up lamp switch / reverse light switch - 84210-12040 Back up lamp switch / reverse light switch connector - the one I purchased is no longer available on amazon but there are other options by searching "back up lamp connector for Toyota" Chapters: 0:00 Flywheel 1:25 Clutch disc and pressure plate 2:47 Input shaft seal 3:50 Throw out bearing and clutch fork 5:38 Cv axle seal 7:34 Speedometer gear swap 8:42 Longer transmission bell housing bolts for manual transmission 9:59 Transmission ground location on transmission 10:41 Engine harness ring location on transmission 10:59 Remaining transmission bell housing bolt 11:32 Heater core coolant pipe modification 12:30 Starter 12:40 Engine and transmission stiffener/brace 13:40 Front transmission mount bracket and clutch slave cylinder with bracket 17:10 Left transmission mount bracket 17:30 Left transmission mount 18:00 Rear engine mount bracket and rear engine mount 18:51 Front transmission mount 19:25 Comparing grounds 19:53 Cv axles 20:03 Transmission ground location on body and transmission 21:39 Left transmission mount showcase on car 22:00 Shifter cables on transmission 25:17 Automatic transmission cooler ports plugged 25:59 Clutch hose 27:56 Brake fluid for clutch system explanation 28:14 Transmission fluid explanation 29:17 Back up switch/reverse switch and connector 30:38 Wiring to get car to start and to get back up/reverse lights to work 36:21 Conclusion