Dtv4 quartz and Cub config, wattage clean, assembling, instructions how I smoke. (EXTRA INFO BELOW) скачать в хорошем качестве

Dtv4 quartz and Cub config, wattage clean, assembling, instructions how I smoke. (EXTRA INFO BELOW)

PROS AND CONS A CUB OR V5 or V4 AT THE BOTTOM WITH LINKS! Some information about how to smoke my Devine tribe version 4 quartz , wattage cleaning, my quartz config, confusing things that confused me about the device. Cleaning tips: use dental scraper tool to get orings off easier/chazz off the quartz bowl.(at dollar store) note: Hold the quartz down with your thumb and screw in if you're having trouble getting ohms under .50 DONT SCREW IN TIGHT MORE THAN 1 TIME, BE GENTLE (ive broke two spacer wires already being rough) If atomizer get stuck to battery. The coil, and cup, both use heat first to loosen put a paper towel on top and twist left looking down. If you can't get it off no matter how much heat. You didn't clean it enough and sadly have to get new device. Maybe can try a wrench or something? "Difference between types of cups Quartz is cold, stubborn, easy to break Titanium is harsh, hot, hard to clean, resilient SiC is easy to clean, expensive, and consistent" My config is at the end of the video. Profile 1– rename Quartz 32W 0.1W Relative (smart off) 100% preheat 0 0 Resistance unlocked Temp control [Set up Pi box yes 0 600 70] Nickle 200 480-420F to use consistently (i use 420) 5c / 10 F Temp dominate yes Change Celsius to Fahrenheit—- Go to screen tab Temp units F How to set autofire to two clicks— Controls.- Multi clicks 2 clicks autofire both TC and VW TO set autofire 0-60 seconds hold fire button and + at same time and you will see the seconds screen pop up, from here you can choose puffs and choose 60 secs. My settings for this page here and how to Change battery shut off to 8 seconds and how to set autofire to 60s. — Advanced tab-settings Power limit-75w Puff cut off-60s RTC mode- LIRC Deep sleep behavior- Turn off device Deep sleep delay-8 minutes Wattage clean donut mode Switch to a VW profile with 0.00 ohms by 3 clicks on the mod to change to the profile and change the wattage with the + & - buttons to 35 or 37. Hold fire button until donut is white again. The donut will sit on top of the spacer. The bump side goes face up on top of the spacer. Hold fire button until white. Instructions to smoke. make sure under 5.0ohms. (if not under 5.0 adjust screws/ straighten wires) mine is at 4.8ohms. Double click auto fire, Let wax bubble underneath the terp pearl(buy at smoke shop) and wait till you start to accumulate a decent amount of fast rising smoke. Click once to end autofire(because if you touch the lid with the screws on accident it'll short out the device), cap it, inhale first hit, auto fire again to milk the dab waiting 5-8 seconds between inhales so more smoke can accumulate under the cap because temp is constantly rising(inhaling cools it down inside each time). keep inhaling till tastes nasty. Autofire again if you need to. Stop autofire with 1 click, uncap WITH A CLOTH IF HEATED WITH WHOLE AUTOFIRE(i burnt my thumb), Clean with qtip. Works well for me so far! If OHMS on top and bottom are different. "One is supposed to be a locked value the mod read when the heater was new (or freshly cleaned), the other is a live reading. If at any point the two stop matching at room temperature, you have a resistance mismatch and need to tighten screws loose or clean dirty crucible. DO NOT TIGHTEN HARD. I BROKE TWO SPACER WIRES. (not cheap to replace have to buy entire bucket or learn to cut them yourself) Tighten screws and turn on and off device to correct ohms reading. CONS AND PROS   / cub_vs_dtv5   "V5: Taller O Ring spacing, grips banger super well!! Atomizer base is large metal, great heatsink Hard to clean and diagnose coil problems Uses four hex screws, two necessary +/- Uses lots of crucible lead length Cub: Great heat time! Instantly gets heated Super easy cleaning and diagnosis Easy to swap coils to disregard a coil problem Familiar atomizer to the V4 Simple build, only a few small pieces to easily lose Gets hot too fast! Gets dirty quick if you disregard it, can make it stop working until clean Take hits very slowly to reduce splatter Wattage clean: 37w auto fire 60 secs until clean. The Cub has a mod you need to do if you already love your V4 MOD NEEDED IF GOING FOR CUB, Get a Dremel and File that metal ring around the bowl off. Reasoning is It makes " it heats quicker, more consistently, immediately, and clean like a dream" (https://seedmass.dev/product/seedmass...) Im going to be buying a CUB with no cap since I can use my V4 cap if on the go. (https://ineedhemp.com/product/the-cub...) + 14MM male 90° Upside down banger and a bubble carb cap with silicone attachment to smoke with turned upside down. (both sold on website) some pretty devices that I wish I could get (https://thedabhut.com/product-categor...) Batteries(can get them cheaper) : https://thedabhut.com/product/molicel... BUY A V5 OUT RIGHT!