1996 - 2000 Toyota Rav4 CV Boot Replacement FULL DIY; Toyota CV axle boot kit shown скачать в хорошем качестве

1996 - 2000 Toyota Rav4 CV Boot Replacement FULL DIY; Toyota CV axle boot kit shown

This video is a full DIY for replacing CV boots using a Toyota CV boot kit. The video shows how to remove the front left axle on a '98 Rav4 AWD automatic, how to disassemble and axle and replace the boots, and how to re-install the axle. This repair is very similar on many other Toyotas. The "other video" mentioned in this video is an even more detailed DIY which shows the shaft seal replacement, but does not show the boot replacement:    • 1996 - 2000 Toyota Rav4 CV Axle Repla...   Check the Pinned Comment for these Timestamps, part numbers, info, and video links: Link to the "other video" mentioned (axle removal & shaft seal replacement):    • 1996 - 2000 Toyota Rav4 CV Axle Repla...   01:15 Set brake, chock wheels, and lift the whole front end 03:25 Remove the wheel (21mm) 03:55 Remove the ABS sensor, if equipped (two 10mm bolts) 04:50 Remove the axle nut cotter key & cover 06:16 Loosen the axle nut (30mm nut, use a 6-point deep socket) 08:03 Remove the sway bar link (two 17mm bolts, H7 hex) 09:39 Remove brake line bracket (12mm) 10:07 Disconnect the tie rod end (17mm, rental tool is OEM Tools 27276) 11:17 Disconnect lower control arm (17mm, two nuts one bolt) 11:57 Remove the axle out from the wheel hub 13:25 Remove the axle cover (two 12mm) 14:02 Remove the axle from the transaxle (slider hammer method shown, rental tool Powerbulit Kit 41 from Advance Auto; also check the other video for other techniques) 16:00 Axle is on the bench; notes about the FSM procedure 18:28 Start on the inboard side: remove the bands/clamps 20:16 Make matchmarks on the shaft, cup, and tripod collar 24:05 Remove the trip "snap-ring" (speared end retaining ring) 24:49 Detail on a recommend tool for this ring (Lang 1407, Proto J250G, Lisle 44900 or similar) 25:42 Remove the tripod from the shaft using a brass punch 26:55 Remove the inboard boot 27:18 Remove the outboard bands/clamps and boot 28:15 Inspect the outboard joint 28:38 Inspect the old grease, decide how to proceed - reboot axle or replace axle? 31:59 Very detailed information on the Toyota boot kit: for this particular application ('98 Rav4 AWD automatic) the part number is 04438-12305; note that some '99 and '00 Rav4's use part number 004438- 12304. Verify your fit with you VIN and a Toyota dealer. 35:49 How to verify which grease goes where 38:41 Prepare to install the outboard boot (inspect and clean) 40:28 Grease the outboard joint (use grease 94304, Raremax LF-G(KAI), 120g) 41:04 Partially install the outboard boot 42:27 Add the rest of the grease to the outboard joint 42:56 Snap the boot into place fully 44:35 Install the outboard boot bands/clamps 52:23 Partially install the inboard boot 53:33 Install the tripod and snap ring 57:03 Very close look at the tripod snap ring to ensure proper install 58:20 Add grease to the trip, inboard boot & cup (use grease 94166, Raremax SLF, 180g) 59:26 Install the inboard cup (tulip) to the boot 01:01:05 Install the inboard boot bands/clamps 01:04:58 Install the axle circlip 01:06:01 Note on the shaft seal (transmission seal) 01:06:29 Grease the shaft seal inner lip and the circlip with MP grease 01:07:21 Re-install the axle: be sure the circlip opening is facing down 01:11:34 Note on re-greasing the wheel bearings while you're in here (I use Lucas X-TRA Heavy Duty Grease) 01:12:27 Re-install the axle cover (12mm) 01:12:40 Re-install the axle to the wheel hub 01:14:52 Connect the wheel hub to the control arm (17mm, torque is 94 ft-lbs) 01:16:32 Connect the tie rod end (17mm & use a new 1/8" cotter key, torque is 36 ft-lbs) 01:17:22 Re-install the sway bar link (17mm & H7 hex, torque is 54 ft-lbs) 01:17:48 Connect the brake line bracket (12mm) 01:17:53 Re-install the ABS bracket and sensor (10mm) 01:18:24 Torque down the axle nut (30mm, torque is 159 ft-lbs) 01:19:28 Install the axle nut cover and a new 5/32" cotter key 01:20:24 Install the wheel (21mm, torque is 76 ft-lbs) 01:20:54 What an axle seal leak looks like (big mess) 01:21:35 Re-fill with ATF (or other fluid/oil for your particular transaxle) 01:22:14 How to check the boot & seal after a test drive Check back to the channel for (hopefully) another axle job for the passenger side axle (4WD auto), as well as a video for the cam plug DIY (to repair the oil leak seen at 02:12). Check the channel for many other Rav4 videos. Thanks for watching, and good luck with your repair!