etrailer | How to Set Up Your Solera RV Slide-Out Awning on a 2022 Jayco Jay Feather Travel Trailer скачать в хорошем качестве

etrailer | How to Set Up Your Solera RV Slide-Out Awning on a 2022 Jayco Jay Feather Travel Trailer

Click for more info and reviews of this Lippert RV Awnings: https://www.etrailer.com/RV-Awnings/L... Check out some similar RV Awnings options: https://www.etrailer.com/dept-pg-RV_A... Click for more info and reviews of this Lippert RV Awnings: https://www.etrailer.com/RV-Awnings/L... Check out some similar RV Awnings options: https://www.etrailer.com/dept-pg-RV_A... Search for other popular Jayco Jay Feather Travel Trailer parts and accessories: https://www.etrailer.com/vehicle/2022... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-s... Hey guys, Kevin here with etrailer. And today I'm gonna be showing you how to install a Solera RV Slide-Out Awning on our 2022 Jayco Jay Feather travel trailer. So the Solera RV Awning is going to do a good job at protecting your Slide-Out. It's going to cover the roof of your Slide-Out so that no rain, no leaves, any other debris fall on the top of your Slide-Out and then get stuck in here when you're closing it up. It's also going to help with water getting down into your wiper seals so that you don't have to worry about any leaks inside of your RV. Because these awnings block the roof of your Slide-Out it's going to save you a whole lot of money and time further down the road. It's going to do a great job at protecting your roof so that you don't have any mold, mildew, any kind of water damage leaking through and ruining the interior or the exterior of your roof, which is also gonna save you from having to replace your roof because it's not quite as easy of a task. And then it also is going to save you a whole lot of time because if you're like me, when I go camping, if I pop out my Slide-Out, I have to get up on the roof or use the ladder to the side, just so I can sweep off any of those leaves or any other kind of debris that ends up on there so that it doesn't end up on the inside of my camper when I close it. So there's a couple things to consider when you're going to purchase a Slide-Out Awning. First, the most important one being the length of it. So to do that, you're actually gonna measure from the outside to the outside edge of the flange. And that's gonna give you, and you're gonna go by inches. We have a facet on our website which will show you the correct awning for that inch. But there's also another issue if you have any clearance. So right now we don't have any issues with our camper but there are other campers where you're gonna have maybe an awning, maybe there's a door in the way or a window or something like that where you're gonna have to back off a little bit and get a smaller size because this arm right here is gonna stick out five to seven inches. So you're gonna need to make sure that you have clearance to that because you don't want that coming into contact with anything when you close up your awning. Alright, I'm gonna show you how to measure this right now. You may need another person to hold the end of your tape measure. I just used a little bit of tape to hold it onto the flange. So you come up to here and it looks like we've got right at 141 inches. So from here, we would take this to our facet and then find the correct slide topper that would match that. So the installation of our awning really isn't that hard. It is just a little awkward, just because of of the size of it. Obviously, if you had a smaller awning it'd be easier to do by yourself. Once you get into your 12 foot to maybe even 18 foot you're gonna need maybe one or two other people just to kind of help you get it in place. Cause these are just a little bit too awkward to handle all on your own. This install was actually a lot easier because it came equipped with the access plates already installed and our extrusion bracket right up at the top there already installed as well. So this install didn't really take that long. Let me show you how I did it. So right out the box, you're gonna have your topper awning. You're gonna have an extrusion rail, your extension rods, your access plates, your access brackets and caps for your extension rail and then an assortment of screws and bolts. The tools that you're gonna need today are a Phillips head screwdriver, an Allen wrench and then some pliers. So luckily on our Jay Feather today, the factory already installed our access plates. If you we're going to do this yourself, say yours did not come with us already installed. What you would need to do is first place some butyl tape over your screw holes in the access plate. Which you can so get on our site. And then you're going to want to put your access plate as far up as you can. And as far over towards the edge of both sides of the T-Molding here. In our