How to Replace Front Disc Brake Pads 2010 to 2022 Chevy Equinox скачать в хорошем качестве

How to Replace Front Disc Brake Pads 2010 to 2022 Chevy Equinox

This video will show and explain How we Replaced the Front Disc Brake Pads on the 2015 Chevy Equinox. Chevrolet Equinox 2.4 Liter 2010 to 2022. 🛠️🧰👨‍🔧🔩⚡ TOOLS, PARTS & MATERIAL USED IN THIS PROJECT: 👨‍🏭⚙️ Brake Pads front and rear:   amzn.to/3ztpf1b   DEWALT ATOMIC 20V MAX* Cordless Ratchet, Brushless, 3/8 in:   amzn.to/3nkkoqj   Ratchet Contour Handle 3/8-inch Drive x 9-inch Long Reach:   amzn.to/35xzd8v   Torque Wrench 3/8-Inch Drive Click 3/8 4 Pcs Set:   amzn.to/49ct3vs   Channellock Pliers Set 12-Inch, 9.5-Inch, 6.5-Inch Made in USA:   amzn.to/3kyphrq   C-Clamp 5 Inch:   amzn.to/399nr58   1/2-Inch Drive Click Torque Wrench:   amzn.to/3pyvsab   1/4-Inch Drive Click Torque Wrench:   amzn.to/3hcg4ju   Floor Jack with Rapid Pump 3 ton Steel Heavy Duty - Orange:   amzn.to/2zm8rhr   Jack Stands Steel (Fits: SUVs and Extended Height Trucks):   amzn.to/3lpfbwn   Heavy Duty Wheel Chock, (Pack of 2):   amzn.to/39uvnbq   DEWALT Socket Set, 3/8-Inch Drive, SAE/Metric, 34-Piece:   amzn.to/2zb5qqp   DEWALT Drive Socket Set, SAE/Metric, 1/2-Inch, 23-Piece:   amzn.to/3lukxjn   DEWALT 20V MAX XR 1/2-Inch Impact Wrench Kit:   amzn.to/32gyyp5   DEWALT 20V 1/4 In. Impact Driver Kit:   amzn.to/36ebofd   12 Inch Adjustable Wrench Crescent Wrench:   amzn.to/3ktuazj   Degreaser ZEP Industrial Purple:   amzn.to/36p3o9y   Synthetic Grease multi-purpose14.1 oz Canister, Translucent White:   amzn.to/3m82g6z   Brake Parts Cleaner CRC 05089 BRAKLEEN:   amzn.to/2irpama   Permatex 25217 Fast Orange Pumice Lotion Hand Cleaner, 1/2 Gallon:   amzn.to/3l1y4q3   “As an Amazon Associate I earn from qualifying purchases at no extra cost to you.” We replace the front disc brake Pads on the 2015 Chevy equinox. Need a new set of front brake pads with all the hardware including grease. Floor jack and 2 jack stands Wheel Chucks 14mm socket Flat Screwdriver 22mm square socket for the wheel lugs and a Torque wrench. chucking the back wheels jack up the front of the car from the center frame until the wheels are off the ground. place the jack stands under the frame and with the 22mm square socket, take off the lug nuts and put the wheel aside. as we can see there's no scrape marks on the rotor this is why we will not be replacing it. It’s easier to get to the back bolts if the wheel is turned all the way to the right. to remove the top and bottom brake pad caliper bolts, use the 14mm slide it out and carefully lay it on top of the upper arm or tie it if necessary. do not let it hang from the hose. using a flat screwdriver, if necessary, remove both brake pads. remove the top and bottom slider brackets before installing the new pad sliders, make sure you clean the surface with a small wire brush if necessary and then smear some grease before clipping the new ones on. remove the bottom and top slide pins from the boot and place some fresh grease on them. it’s important that you put the pins back in the same place you take them out, since they are slightly different... and make sure they clip back into the boot collar so no water and dirt gets in them. if the boot is damaged, replace it we take the new slider brackets included in the kit and place one on the top and bottom of the caliper bracket Make sure the slide clips are centered and the tabs are bent over the sides. this is to avoid them from moving side to side and hit the rotor. bend them on each side of the top and bottom clip. before installing the new inside brake pad, make sure this plate is transferred over from the old one, the inside pad is identified by the squeal tab here, when the pads get too low this tab comes in contact with the rotor and you will hear that squeal before installing the new brake pads, put a little grease on each end that will come in contact with the slider, then do the same to the other side, now we're ready to put the caliper back but first we need to push the cylinder in, so it won’t interfere with the new thicker pads. using an old pad and a C clamp, slowly tighten the cylinder into the caliper then insert it back on to the caliper bracket line it up with the top and bottom slide pins and thread in the 2 bolts then torque them to 30 ft. lbs. while holding the pins with channel locks to stop them from spinning. put the wheel back on and hand tighten the lug nuts lower the jack till the tire touches the ground torque them in a 'star' pattern to 140 ft. lbs. pump the brake pedal between 5 and 10 times to make sure its firm and drive a few miles to make sure. See Chevrolet Equinox 2010 to 2017 Playlist for more;    • How to Replace a Battery 2010 to 2017 Chev...   See Jeep Cherokee Trailhawk 2014 to 2017 Playlist for more;    • How to Replace Battery 2017 Jeep Cherokee ...