Скачать с ютуб видео DIY CNC Plasma Cutter for 300$

Не удается загрузить Youtube-плеер. Проверьте блокировку Youtube в вашей сети.
Повторяем попытку...

Скачать видео с ютуб по ссылке или смотреть без блокировок на сайте: DIY CNC Plasma Cutter for 300$ в качестве 4k

У нас вы можете посмотреть бесплатно DIY CNC Plasma Cutter for 300$ или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:

Информация по загрузке:

Скачать mp3 с ютуба отдельным файлом. Бесплатный рингтон DIY CNC Plasma Cutter for 300$ в формате MP3:

Если кнопки скачивания не загрузились НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу страницы.
Спасибо за использование сервиса ClipSaver.ru

DIY CNC Plasma Cutter for 300$

Follow me on Facebook and Instagram for more updates Instagram : Scantrons_Garage Facebook: Turk Turkleton Email [email protected] Thanks for watching! Please send me any questions or comments you may have to improve this DIY CNC Plasma Cutter. This was a fun project. I basically just converted a cheep laser engraver used for hobbies and strapped on a plasma cutter creating a simple home purpose plasma CNC cutter. Total money I spent just over 300$ for the laser engraver and the plasma cutter. I used some scrap metal to make the cutting table which served two purposes: this made a proper cutting surface and raised the cutting surface closer to the plasma head. This was needed to gain clearance where the plasma torch will not interfere with the engraver frame. Wiring: I could have spent more time figuring out the relay system. From what I understand, If I move the engraver driver further away from the plasma cutter head, this will decrease the amount of electrical signal interference. Also adding wiring shielding would help with this. All in all, I think the thumb button was the easiest way to go about this. Product information: * VEVOR 5W Laser Engraver* https://amzn.to/474MT6f *Plasma Cutter* VEVOR CUT-50 https://amzn.to/481IRwQ The only other parts needed are some wiring Items: 18 Gauge wire wire crimp connectors Automotive relay (If you decide to go this rout) *Thumb Switch* Momentary on switch or "mom" switch CAD Software: Laser GRBL: worked just fine for the simple stuff Light Burn: This is a product for purchase. the software license is 89.00. They offer a 30 day free trial which is what I used to make everything in this video. I will purchase this if I don't go with the fusion 360 program. Sheet metal Cut Speed suggestions: Increase the pause time to 1500 if using the thumb button 16 gauge speed 10mm/sec or 0.4in/sec depending if your metric or not. advanced start pause 800 check cut though end pause 1000 14 gauge Speed 8mm/sec or 0.3in/sec depending if your metric or not. start pause 1000 check cut though end pause 1000 10 gauge speed 7mm/sec or 0.276in/sec depending if your metric or not. advanced start pause 1200 check cut though end pause 1000 3/16 speed 5mm/sec or 0.2in/sec depending if your metric or not. advanced start pause 1500 check cut though end pause 1000 1/4 speed 3mm/sec or 0.11in/sec depending if your metric or not. advanced start pause 1600 check cut though end pause 1000 Vigilance by Ghostrifter Official https://bit.ly/ghostrifter-sc Creative Commons — Attribution-NoDerivs 3.0 Unported Free Download / Stream: https://bit.ly/3Qmaqs4 Music promoted by Audio Library • Vigilance – Ghostrifter Official (No ... –––––––––––––––––––––––––––––– #cnc #diy #homemade #cncplasmacutter #amazon

Comments