How I ride tight, technical switchbacks скачать в хорошем качестве

How I ride tight, technical switchbacks

My full riding tutorial on how to best ride tight, technical switchbacks like these on a mountain bike is posted here:   / 3-ways-to-33345804   If you want to learn more about that Ibis Ripmo AF I'm riding, visit this link: https://bit.ly/IbisRipmoatJensonUSAjkw (affiliate) Mentally, I try to think of switchbacks as flat berms. While that might seem like a contradiction, I use a similar body positioning and technique that I employ on berms, but adjust it for the lower speed and reduced traction. On berms, I keep the bike perpendicular to the riding surface, engaging the center knobs of the tire with the dirt. However, when a berm is not present, I lean the bike down into the turn in order to engage the side knobs. I lean the bike less when I’m going slower, and I drop my outside pedal more on the slower, flatter turns. Delving a little deeper into that mentality, I generally use three techniques for switchbacks: Pumping the turn like a regular, wider flat corner or berm (my personal favorite) Nose wheelie through the turn Power sliding the bike through (known as a cutty) A lot of folks do a Scandinavian flick, but I rarely see that as faster. It takes more energy and will be even less consistent than a regular pump. So how do we use these three techniques? The universal steps, regardless of the technique, are: Step 1: do your braking before you get to the turn. It’s much faster to slow too early and nail exit speed than to tip over and crash. All three techniques will require braking before reaching the turn. Step 2: analyze the turn. Is it wide enough you can do the best technique of leaning and pumping the bike? Is there an available entrance wall to help begin the turn early? Or is it so tight that a stoppie is best? Is the turn so tight, and is traction so low, that a cutty will be most effective? Frustratingly enough, being able to correctly analyze a turn at speed will only come with more experience. But enjoy it! Learning how to anticipate what will happen in each corner is one of the greatest pleasures in mountain biking. Step 3: plan for the exit. Once you have your strategy sorted, how can you maximize your exit speed and control? After considering those three steps, decide on the technique that will be best. FYI, I reviewed my general cornering theories back in June here:   / 27981205  . If you can’t tell already, my favorite of these three methods is to rail and pump through the turns like a berm, with adjustments made to the lean angle depending on the trail speed. This is a very consistent way to corner and the big pump that it generates will help you build a great exit speed. Not to mention it keeps the air in your tires and the trail intact! The nose wheelie is my go to on very tight corners or when I need to scrub a bunch of speed. The nose wheelie tutorial from April is helpful in case you haven’t seen it (  / 26296762  . The nose wheelie means you’ll never come out of the switchback going any faster than you came in, and it can often bring you to a full halt. Not fast. But it looks cool, and it’s an easy way of slowing yourself while finding your line in a very small amount of space. And the cutty- not my go-to move, but still, quite practical when in a switchback situation, especially one without much traction. Compress the bike so that it’s rebounding while you are turning. Slow before initiating the cutty, use your arms to counter steer as necessary. Keep your eyes looking towards the exit. Weight is centered. Use pressure on your inside foot to push the bike, and be ready to apply pressure on the outside foot to control and stop the resulting slide. Since we filmed this video in Mexico, I actually did a full tutorial on cutties here:   / 36579859   Stay tuned- lots of great content to come thanks to Jenson USA, and you can check them out here via my affiliate link: https://www.jensonusa.com/blog/rider-... General Affiliate Links: Jenson USA: https://bit.ly/JensonUSA2022JKW Industry Nine: https://bit.ly/IndustryNine2022JKW PNW Components: https://bit.ly/PNWComponents2022JKW Shimano: https://bit.ly/Shimano2022JKW Ever notice that PNW logo on my handlebars? No, I’m not repping my locale that hard- or wait, maybe I am- but that’s actually a company that my friend Aaron runs! PNW Components makes some high end controls, including bars, stems, grips, dropper posts, levers, and a few other awesome items. Have a peek at their beautiful site through my affiliate link here: https://bit.ly/PNWComponents2022JKW Big thanks to these guys for making this all possible! Any purchases from these links will directly help support my channel as well: Jenson USA: http://bit.ly/JensonJKW PNW Components: https://bit.ly/PNWcomponentsJKW Industry Nine: http://bit.ly/IndustryNineJKW Ibis Cycles: http://bit.ly/IbisJKW