Let’s Paint some Underhood Black Single Stage Tamco w/ Luma III Shadow Primer gun 1.3 Tip скачать в хорошем качестве

Let’s Paint some Underhood Black Single Stage Tamco w/ Luma III Shadow Primer gun 1.3 Tip

Underhood Satin Black Single-Stage paint is designed to offer a satin sheen that is both user- friendly and of high quality. You can achieve a professional-looking satin finish, yet have an easy application. Our formulation helps achieve an even and smooth coverage. This makes Underhood Satin Black an ideal choice for automotive underhood applications where a durable yet attractive finish is desired. Features & Benefits Ideal for Custom, Fleet & Industrial Overall & small applications Satin Finish Easy to spray / User friendly Integrates with HC4100 Glamour Clearcoat Multi use UV resistance Durable (excellent weathering) Compatible Surfaces Sanded Tamco® DTM Primer Sanded Tamco® DTA Epoxy Sanded Tamco® High Build Epoxy Tamco® Forever Seal Other premium primers, epoxies or sealers but no warranty implied Required products HH76XX series Hardeners. HH7603 Fast HH7605 Medium HH7607 Slow Optional HR1370 HR1380 HR1390 HP1001 Accelerator HP1010 Fisheye Eliminator HR900 Retarder HP Flat Pot Life Extender Flo N Go (See our" What Temperature should I choose PDF" for a guideline on which suits your current job) Info@TamcoPaint.com www.TamcoPaint.com (757) 627-9551 1-5 Underhood Satin Black Single Stage Surface Preparation: Throughly cleaned with HR398 Final Wipe and wipe dry with clean cloth. Plastics: Clean with HR397W Waterbourne Wax & Grease Remover using a Scotch-Brite pad, wipe dry with clean cloth. Mix Ratio: Component Volume AG Underhood Satin Black Single Stage 4 HH7603/7605/7607 Activator 1 Note: Tamco® reducer can be added up to 10% as needed. Use only Tamco® Reducers. Our reducers are completely moisture free. Moisture in reducer will kill the shine of your singlestage coating. HH7603 - Fast 60-75°F Large areas 65-70°F HH7605 - Medium 75-80°F Large areas 70-80°F HH7607 - Slow 85-100°F Large areas 80-90°F HH7607 will be 87-100°F you may need to add 5% HR900 retarder in hot humid conditions. Additives: HR900 Retarder, Pot-Life Extender, HP1001 Accelerator, HH1010 Fisheye Eliminator, Flo N Go: 1-2 oz per spray able Quart. HR Reducers: up to 10% HP Flat: Refer to our HP Flat TDS sheet for mixing instructions. Air Pressure & Gun Setups: Gun Setups: HVLP Siphon Feed: 1.2 mm – 1.4 mm Gravity Feed: 1.2 mm – 1.4 mm Conventional Siphon Feed: 1.2 mm – 1.4 mm Gravity Feed: 1.2 mm – 1.4 mm 25-29 PSI at the gun 5-10 PSI at the cap Air Pressures Conventional: Always refer to your gun manual for their advice in using our products. Info@TamcoPaint.com www.TamcoPaint.com (757) 627-9551 2-5 Underhood Satin Black Single Stage Application: 1. 2. 3. 4. 5. 6. Refer to Tamco® Epoxies TDS,Tamco® Primers TDS & Tamco® Sealers TDS for flash times before top coating with your singlestage. Apply 1 medium wet coat. Allow 20-30 minute flash at 78°F between coats. Apply only 3 coats of color for each session. Shop conditions temperature and air flow will determine flash times. Monitor an area by lightly touching. If the color is still wet or stringing do not apply additional coats. Wait until singlestage becomes tacky but doesn’t string. Do not apply more singlestage after 1 hour of dry time. Drying Times: Airdry: 12-16 hours @ 78°F. Tape Time: 6-8 hours Baking: 140°F for 30 minutes Wet Sanding: Sand with 400-600 grit if re-coat is needed Recoat: If you choose to apply additional coats of singlestage, after sanding you can add 5% Tamco® reducer and apply 1 medium coat followed by 2 more medium wet coats with 20-30 minute flash between. As above shop conditions will vary flash times so “string” test is recommended Polishing: n/a Do not wax for 120 days Info@TamcoPaint.com www.TamcoPaint.com (757) 627-9551 3-5 Underhood Satin Black Single Stage Tamco® Tips: Tips: To increase air dry time, a minimum temperature of 60°F must be maintained. Sanded surface should be re-sanded if not top- coated within 8 hours. Extra reducer may be required In High Temps using HR1390 Extra Slow Reducer or HR900 retarder. When using hardeners, be sure the mixture is stirred throughly. We recommend no longer than 1 hour application time between coats for maximum adhesion. Shop conditions, Temperature and air flow will determine flash times. The “string” test method can be used to determine temperature and air flow will determine flash times. The “string” test method can be used to determine proper flash time for your conditions. When spraying Underhood Satin Black SingleStage, bumping your PSI up 1-2 bars will help with flattening. Wet sanding or polishing will bring back sheen. Note: Use only Tamco® Reducers. Equipment Cleaning: Lacquer Thinner or HR1360 is an excellent cleaner. Cold Shop Conditions: Do not spray under 65°F or above 100°F. Info@TamcoPaint.com www.TamcoPaint.com (757) 627-9551 4-5 Underhood Satin Black Single Stage https://cdn.shopify.com/s/files/1/025...