ZK-4KX DC Buck Boost Converter Module Setting Method CC CV 30V 4A скачать в хорошем качестве

ZK-4KX DC Buck Boost Converter Module Setting Method CC CV 30V 4A

@radal05 Module DC Buck Boost Converter CC CV 30V 4A with LED Display - ZK-4KX spesifikasi manual datasheet Jual ZK-4KX ZK4KX DC DC Step Up Down Buck Boost Link pembelian : 1.https://tokopedia.link/kD41GPKckxb 2. Cek ZK-4KX ZK4KX DC-DC Buck Boost Converter CC CV 0.5-30V 4A - AIFRobotic dengan harga Rp120.000. Dapatkan di Shopee sekarang! https://shope.ee/AKAcYcyIKW?share_cha... Spesifikasi Berikut spesifikasi dari alat penurun tegangan ini: Input undervoltage protection (4.8-30v adjustable, default 4.8v) Output overvoltage protection (0.5-31v adjustable, default 31V Output overcurrent protection 0-4.1a (adjustable, default 4.1a) Overpower protection (0-50w adjustable, default 50W) Overtemperature protection (80-110C adjustable, default 110?) Timeout protection (0-100h adjustable, off by default) Super capacity protection (0-60ah adjustable, off by default) Operating frequency: 180KHZ Input voltage: 5.0-30v Output voltage: 0.5-30v Output current: can work stably at 3A for a long time, and can reach 4A Output power: natural heat dissipation 35W, strengthen heat dissipation 50W Voltage display resolution: 0.01V Current display resolution: 0.001A Conversion efficiency: about 88% Method of Use: 1. Switch display parameters -- in the normal interface, press SW to switch the display below the display screen, and switch the display content between current A power W capacity Ah time h.Long press SW button to switch the uplink display on the display screen and switch the display content between input voltage IN output voltage OUT. 2. Set output voltage -- press U/I button in the normal interface to enter the interface of setting voltage constant current.It can be seen that a certain digit of the output voltage value is flashing. Rotate the encoder left and right to adjust the major and minor.Short press the rotary encoder to choose which bit of output voltage to set.After setting, press U/I button 2 times to return to the normal interface.Or automatically return to the normal interface after stopping operation for 10s. 3. Set constant current value (that is, the maximum current value allowed to output by the module) -- press U/I button in the normal interface to enter the setting voltage constant current interface.Then press U/I button and switch to setting constant current value. You can see a bit of the setting constant current value flashing. Rotate the rotary encoder left and right to adjust the major and minor.Short press the rotary encoder to choose which bit to set the constant current value.After setting, press U/I to exit the setting voltage constant current interface and return to the normal interface.Or automatically return to the normal interface after stopping operation for 10s. 4. Set the default on/off state of module power-on -- long press U/I in the normal interface to enter the parameter setting interface.You can see that it shows 'OPEN OFF' or 'OPEN ON'. 'OPEN OFF' means the output is turned OFF by default when power is ON, and 'OPEN ON' means the output is turned ON by default when power is ON.Long press rotate encoder to switch two states.After setting, long press U/I to return to the normal interface. 5. Setting of protection parameters on state and threshold -- long press U/I to enter the parameter setting interface in the normal interface.Press SW until the protection you want appears.LUP -- undervoltage protection threshold;OUP -- overvoltage protection threshold;OCP -- overcurrent protection threshold;OPP -- over power protection threshold;OAP -- ultra-capacity protection threshold;OHP timeout protection threshold;OTP -- overtemperature protection threshold.Short press rotate encoder to select which bit you want to set the protection parameter.Long press the rotary encoder to set the protection parameters on or off (only timeout protection and supercapacity protection can be set to turn on/off, and other protection parameters are turned on by default.).Rotate the encoder left and right to make the parameters bigger and smaller.After setting, long press U/I to return to the normal interface. 6. Calibration voltage and current -- press U/I button to enter the parameter setting interface under normal interface.Press SW until a parameter interface with CAL appears.The calibration input voltage interface with the symbol CAL+IN+V;The calibration output voltage interface with the symbol CAL+OUT+V;The calibration output current interface with the symbol CAL+OUT+A.Rotate the encoder left and right to adjust the size of parameters.After the adjustment is completed, long press the rotary encoder to confirm the adjustment is completed, and the parameter value is no longer flashing.Long press U/I to return to the normal interface. 00:00 Radal05 00:12 Power supply serbaguna ZK-4kX 00:55 Kenapa murah 02:00 Input yang paling cocok 03:00 Spesifikasi ZK-4kx 06:00 Cara setting Zk-4kx