Code P0336 RX-8 won’t start on hot and bad idling | Fixed Replaced crankshaft position sensor скачать в хорошем качестве

Code P0336 RX-8 won’t start on hot and bad idling | Fixed Replaced crankshaft position sensor

Code P0336 RX-8 won’t start on hot and bad idling | Fixed Replaced crankshaft position sensor Mazda RX-8 Related Service videos 1. How To Install RX-8 Spark Plugs Correctly with 2 Trailing Spark Plugs on top and 2 Leading on bottom    • How To Replace Mazda RX-8 Spark plugs what...   2. How to install Ignition Coils in correct order with Leading 1 Trailing 1 Leading 2 Trailing 2    • Code P0300 Mazda RX-8 Misfiring Cylinder 1...   3. Mazda RX-8 P0661 Check Engine code problem solved    • Mazda RX-8 P0661 Code Fixed for $20 SSV So...   4. How to Pre Mix 2 Cycle Engine Oil into Mazda RX-8    • Pre Mixing How to Pre mix 2 Cycle oil into...   5. Mazda RX-8 P0661 Code How to test Solenoids correctly to find the bad ones    • P0661 Code? How to diagnose / Test MAZDA R...   RX-8 Stalling out when parking or RX-8 has a Ruff idle and multiple cylinder miss fire, RX8 is not running right and quits running after 5 mins Please help, if this is happening to you, try replacing your crank shaft position sensor also known as eccentric shaft position sensor, new ignition coils and spark plugs will help it helped me Mazda RX-8 Forum questions and answers hey guys...im hoping you guys could give some advice on probable causes. one night i parked my car and the next morning it didnt start!. i checked the battery and it tested out bad, so i replaced it! then my starter wouldnt disengage so i replaced the starter also.... still no start. i've checked fuses and relays. i even tried push starting my car, NOTHING. my car is cranking over but it aint starting. i have had my ignition system replaced already at the dealer about a year ago. i dont know what to look for... i 've done pretty much everything i can think of....if you guys can help me with this, i would appreciate it. thanks! Was the engine fully warmed up when you parked the car and shut it down? If the engine was not fully warmed up, it may be flooded. Never shut down a rotary engine without warming it up. Check your user manual for instructions on de-flooding the car. Or check out the DIY section of this forum for other techniques used by members to de-flood the engine. Otherwise if the car is still under warranty, you may want to have Mazda check it out. Reply if its flooded, thats one hell of some flooding that happen...i've cranked it over and over...ive spent a week and a half trying to get it working! im clueless.. Reply Then I assume you've been through these already to verify the engine isn't flooded? http://www.finishlineperformance.com...5-08-1883f.pdf https://www.rx8club.com/showthread.p.... https://www.rx8club.com/showpost.php.... Usually one of these will get it going, unless there is something else wrong. Have you check to make sure the spark plug wire boots didn't come loose? How about disconnecting/reconnecting the ESS? Take out and clean/dry the plugs. While they are out, crank the engine with the pedal to the floor, for twenty seconds or so. Re-install plugs and connect the right coil to each plug (from front coil - FL, FT, RL, RT) After a good battery charge, try to start...... Good luck. unlikely here... but if it is not flooded or spark related... squirt some starting fluid into the little guy and see if it sputters or gets anything... just to see if its fuel delivery hey same thing happen to me if engine flooded you need connect the battery to another car take out the fuel pump fuse crank the engine untill you feel the compression again. replace the fuel pump fuse crank it again untill engine start. keep some pauses between cranks to save the starter motor Reply Cranks, won't Start. HELP!!! hey guys... My car has been acting up lately. About 3 weeks ago, I took off the muffler and then drove it like that till recently. Was driving to the store and at a stop light, the car just stalled then won't start. Then it will only start when cold but stalls when warm. 2 days ago, I started it again and it started but got a P0301 check engine code (flashing) and when i depressed the clutch, it just stalled. Put the muffler back on and now it won't start but cranks. I assume the spark plugs are flooded. Went to advance and they told me that I have to balance the engine to put new spark plugs on but I looked on all data and it doesn't say so. Anyways, I checked voltage on coils, getting proper voltage there. Getting proper voltage at the eccentric shaft position sensor. Not getting spark. What could cause this? Reply balance the engine before putting spark plugs in? talk about full of ****! are u sure u not gettinf spark? u need can find out with a 6 -7 bucks tool, thanks for the reply. haha he also mentioned that he worked at mazda before. I tried several spark tests and it seemed like i was not getting spark. Im changing spark plugs today and prob doing a compression test. This all happened 2 weeks after I took my muffler off. Maybe when it was off, it was reading a lot of oxygen so it was dumping fuel then making it stall. That is my belief. I put the muffler back on and reset the ECM by pressing the gas pedal 20x