• ClipSaver
  • dtub.ru
ClipSaver
Русские видео
  • Смешные видео
  • Приколы
  • Обзоры
  • Новости
  • Тесты
  • Спорт
  • Любовь
  • Музыка
  • Разное
Сейчас в тренде
  • Фейгин лайф
  • Три кота
  • Самвел адамян
  • А4 ютуб
  • скачать бит
  • гитара с нуля
Иностранные видео
  • Funny Babies
  • Funny Sports
  • Funny Animals
  • Funny Pranks
  • Funny Magic
  • Funny Vines
  • Funny Virals
  • Funny K-Pop

Making the Ultimate Retrobrighting Box скачать в хорошем качестве

Making the Ultimate Retrobrighting Box 4 года назад

скачать видео

скачать mp3

скачать mp4

поделиться

телефон с камерой

телефон с видео

бесплатно

загрузить,

Не удается загрузить Youtube-плеер. Проверьте блокировку Youtube в вашей сети.
Повторяем попытку...
Making the Ultimate Retrobrighting Box
  • Поделиться ВК
  • Поделиться в ОК
  •  
  •  


Скачать видео с ютуб по ссылке или смотреть без блокировок на сайте: Making the Ultimate Retrobrighting Box в качестве 4k

У нас вы можете посмотреть бесплатно Making the Ultimate Retrobrighting Box или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:

  • Информация по загрузке:

Скачать mp3 с ютуба отдельным файлом. Бесплатный рингтон Making the Ultimate Retrobrighting Box в формате MP3:


Если кнопки скачивания не загрузились НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу страницы.
Спасибо за использование сервиса ClipSaver.ru



Making the Ultimate Retrobrighting Box

In this video I'll explain how top make this box for retrobrighting aka removing yellowing from plastic. More info of the actual retrobrioghting process can be found from this tutorial    • How to remove yellowing from old plastic (...   Parts list at the bottom First you need a box. Make sure it's as big as you will ever need. I recommend buying 2 of them (if it's transparent). This way you have the largest possible container to but your yellowed item in when you stack them inside each other. I always recommend using as small continer as possible, and especially one with the smallest possible surface area, this will minimize evaporation and save you some hydrogen peroxide. The box is lined with aluminum tape to keep in the heat and light better. Aluminum tape is real metal so it is conductive, I used transparent tape to isolate my UV LED strip from the metal to reduce the risk of shorting. The strips were attached inside the box and the lid of the box with even spacing. Next the strips were soldered together and the strips on the lid were connected to the other strips with a long wire to allow enough movement for the lid. Next I used W1209 temperature control board. It's a board which can be used to turn on and off heating/cooling devices based on temperature. here's a complete guide for the settings: http://www.kelco.rs/katalog/images/17... The important settings are, P0, you need to choose H for heating. (you can use this to control AC or a fan and for cooling, thee you would choose C). For P1 I used the standard 2.0. This determines how much bellow of the target temperature the temperature need to go before the heater turn on. I set my target temperature for 50 degrees Celsius (ALL THE TEMPERATURES DISPLAYED ARE CELSIUS!). So with my settings when the temperature drops bellow 48 C it will start heating again and stop at 50 C. In this setup I made 3 separate circuits. 1. LED lights, which are controlled by the green switch and the power input is on the left. I use 12V for that because that's what my leds are rated for. 2. Circuit for the heater. It goes from the middle power plug to the heating unit through the relay on the W1209 board (KO and K1 connectors) There is no switch because the relay will turn heating off when the power of the control board is off I use 12V power and 12V heater for this ( but the heater can easily be upgraded to one that uses mains power if needed). 3. Power for the control board. It goes from the rightmost power plug to the positive and negative terminals on the W1209 board. It's very important to only use 12V power on this one, higher voltage will break the board. As mentioned for the heater I chose 12V submergeable heating unit. I felt this is the safest option as I only need to make sure it will stay in the solution to prevent it from over heating. The bellow links are affiliate links and I get a small commission if you buy anything from the site after using the links. To support my channel you can do all your online shopping through these links. Here is the parts list: Aluminum tape: https://amzn.to/2S3C6s1 UV LED strip: https://amzn.to/3vogftL Controller board (W1209): https://amzn.to/3aIpoWn Heating element: https://amzn.to/3aLud0Z Power source: https://amzn.to/32QMg1h Power jack: https://amzn.to/3tX4udH Switch: https://amzn.to/2PvnqRK Pair Wire: https://amzn.to/3dSXNUi Tools: Electric screwdriver: https://amzn.to/2QsZf75 Soldering station: https://amzn.to/3xrpv25 Wire stripping tool: https://amzn.to/3u10E2F Hydrogen peroxide: https://amzn.to/2K5OmTS​ Flux paste: https://amzn.to/2R3Idfw Hot glue gun: https://amzn.to/32RGlZQ

Comments

Контактный email для правообладателей: [email protected] © 2017 - 2025

Отказ от ответственности - Disclaimer Правообладателям - DMCA Условия использования сайта - TOS



Карта сайта 1 Карта сайта 2 Карта сайта 3 Карта сайта 4 Карта сайта 5