Скачать с ютуб видео NISSAN/INFINITI ECU/THROTTLE/IDLE RESET& RELEARN VERY IMPORTANT FOR 350Z/G35/G37/FX35/370Zetc DIY

Не удается загрузить Youtube-плеер. Проверьте блокировку Youtube в вашей сети.
Повторяем попытку...

Скачать видео с ютуб по ссылке или смотреть без блокировок на сайте: NISSAN/INFINITI ECU/THROTTLE/IDLE RESET& RELEARN VERY IMPORTANT FOR 350Z/G35/G37/FX35/370Zetc DIY в качестве 4k

У нас вы можете посмотреть бесплатно NISSAN/INFINITI ECU/THROTTLE/IDLE RESET& RELEARN VERY IMPORTANT FOR 350Z/G35/G37/FX35/370Zetc DIY или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:

Информация по загрузке:

Скачать mp3 с ютуба отдельным файлом. Бесплатный рингтон NISSAN/INFINITI ECU/THROTTLE/IDLE RESET& RELEARN VERY IMPORTANT FOR 350Z/G35/G37/FX35/370Zetc DIY в формате MP3:

Если кнопки скачивания не загрузились НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу страницы.
Спасибо за использование сервиса ClipSaver.ru

NISSAN/INFINITI ECU/THROTTLE/IDLE RESET& RELEARN VERY IMPORTANT FOR 350Z/G35/G37/FX35/370Zetc DIY

You have to do this after every ECU reset, every modification, tuning, etc. Without this steps, installing of CAI, plenum spacer and another modes will not give you anything except sound. To get the power, watch the video and follow instructions. Enjoy the power! :) Step 1: Reset ECU and fuel maps. Disconnect negative wire and really quick pump you brake pedal 3-5 times and wait 20 minutes. After that, before you will wear negative connection back, pump the brakes again 3-5 times. Step 2: Learning. Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON. 1. Confirm that accelerator pedal is fully released, turn ignition switch "ON" and wait 3 seconds. 2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds. 2a. Fully depress the accelerator pedal (HARD). 2b. Fully release the accelerator pedal. 3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking. 4. Fully release the accelerator pedal (while the CEL is still blinking) 5. Wait about 10 second. 6. Fully depress the accelerator pedal and keep it for more than 10 seconds. 7. Fully release the accelerator pedal (The CEL light will continue to blink). 8. Turn ignition switch to "OFF" position and now you can start the car. The CEL light should be gone. If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU. Accelerator Pedal Release Position Learning Operation Procedure 1. Make sure that the accelerator pedal is fully released. 2. Turn ignition switch "ON" and wait at least 2 seconds. 3. Turn ignition switch "OFF" wait at least 10 seconds. 4. Turn ignition switch "ON" and wait at least 2 seconds. 5. Turn ignition switch "OFF" wait at least 10 seconds. Throttle Valve Closed Position Learning Operation Procedures 1. Make sure that accelerator pedal is fully released. 2. Turn ignition switch to "ON". 3. Turn ignition switch to "OFF" wait at least 10 seconds. Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound. Idle Air Volume Learning (Throttle Position Learning) It is better to count the time accurately with a clock. 1. Perform "Accelerator Pedal Released Position Learning". 2. Perform "Throttle Valve Closed Position Learning". 3. Start engine and warm it up to normal operating temperature. 4. Turn ignition switch "OFF" and wait at least 10 seconds. 5. Confirm that the accelerator pedal is fully released, then turn ignition switch "ON" and wait 3 seconds. 6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds. 7a. Fully depress the accelerator pedal (HARD) 7b. Fully release the accelerator pedal. 8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON. 9. Fully release the accelerator pedal within 3 seconds after the CEL is ON. 10. Start engine and let it idle. 11. Wait 20 seconds. 12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications. Be Sociable, Share!

Comments