Π£ Π½Π°Ρ Π²Ρ ΠΌΠΎΠΆΠ΅ΡΠ΅ ΠΏΠΎΡΠΌΠΎΡΡΠ΅ΡΡ Π±Π΅ΡΠΏΠ»Π°ΡΠ½ΠΎ Anodizing Aluminium - No Sulphuric Acid and Less Than $50 To Do (Sodium Bi-Sulphate) ΠΈΠ»ΠΈ ΡΠΊΠ°ΡΠ°ΡΡ Π² ΠΌΠ°ΠΊΡΠΈΠΌΠ°Π»ΡΠ½ΠΎΠΌ Π΄ΠΎΡΡΡΠΏΠ½ΠΎΠΌ ΠΊΠ°ΡΠ΅ΡΡΠ²Π΅, Π²ΠΈΠ΄Π΅ΠΎ ΠΊΠΎΡΠΎΡΠΎΠ΅ Π±ΡΠ»ΠΎ Π·Π°Π³ΡΡΠΆΠ΅Π½ΠΎ Π½Π° ΡΡΡΠ±. ΠΠ»Ρ Π·Π°Π³ΡΡΠ·ΠΊΠΈ Π²ΡΠ±Π΅ΡΠΈΡΠ΅ Π²Π°ΡΠΈΠ°Π½Ρ ΠΈΠ· ΡΠΎΡΠΌΡ Π½ΠΈΠΆΠ΅:
ΠΡΠ»ΠΈ ΠΊΠ½ΠΎΠΏΠΊΠΈ ΡΠΊΠ°ΡΠΈΠ²Π°Π½ΠΈΡ Π½Π΅
Π·Π°Π³ΡΡΠ·ΠΈΠ»ΠΈΡΡ
ΠΠΠΠΠΠ’Π ΠΠΠΠ‘Π¬ ΠΈΠ»ΠΈ ΠΎΠ±Π½ΠΎΠ²ΠΈΡΠ΅ ΡΡΡΠ°Π½ΠΈΡΡ
ΠΡΠ»ΠΈ Π²ΠΎΠ·Π½ΠΈΠΊΠ°ΡΡ ΠΏΡΠΎΠ±Π»Π΅ΠΌΡ ΡΠΎ ΡΠΊΠ°ΡΠΈΠ²Π°Π½ΠΈΠ΅ΠΌ Π²ΠΈΠ΄Π΅ΠΎ, ΠΏΠΎΠΆΠ°Π»ΡΠΉΡΡΠ° Π½Π°ΠΏΠΈΡΠΈΡΠ΅ Π² ΠΏΠΎΠ΄Π΄Π΅ΡΠΆΠΊΡ ΠΏΠΎ Π°Π΄ΡΠ΅ΡΡ Π²Π½ΠΈΠ·Ρ
ΡΡΡΠ°Π½ΠΈΡΡ.
Π‘ΠΏΠ°ΡΠΈΠ±ΠΎ Π·Π° ΠΈΡΠΏΠΎΠ»ΡΠ·ΠΎΠ²Π°Π½ΠΈΠ΅ ΡΠ΅ΡΠ²ΠΈΡΠ° ClipSaver.ru
Anodizing Small Parts without using Sulphuric Acid and with a total cost of less than $50. This is a guide on how I anodize small aluminium parts to give them an aesthetic anodize, using sodium bi sulphate, in place of sulphuric acid. This is about as basic as a set up as it can be, and I want to show you that we can still achieve great results on small parts. However there are some constraints to be aware of: We are not aiming for an exact thickness of oxoide, however if you let the current drop to near zero, it should be thick enough to take up the dye some dyes will take up better than others. Rit black and other black dyes have a reputation for being more difficult to get good finishes on sodium bi-sulphate is reportedly a safer acid than sulphuric acid, but 20% bi-sulphate is still a dangerous chemical and should be handed carefully as the part grows in size and complexity, bubbles may become an issue and will need to be removed though the use of a stir or bubbling method anodizing coats thinner than 30-40 microns generally do not provide hard wear resistance This guide is intended for basic aesthetic coats for small parts Whilst the process is straightforward, it will take a few goes to get right As a final note, whilst anodizing can be a straightforward method, I only recommend doing it if you feel that it needs to be done, in this case to add colour. I have done many aluminium parts over the years and most of them did not need to be anodized and were left bare, given a coat of etch primer and painted, or given a coat of clear lacquer. #machining #diy #anodizing