How To Embroider With the MagnetFrame | Avance 1501C & 1201C скачать в хорошем качестве

How To Embroider With the MagnetFrame | Avance 1501C & 1201C

How To Embroider With the MagnetFrame | Avance 1501C & 1201C If you’ve just purchased a MagnetFrame kit and want someone to show you how it works and how to use it, then stick around to the end of this instructional article. You’ll read about two models of this kit — each one is designed for use with either the Avance 1201C or 1501C embroidery machines. First, let’s understand what the MagnetFrame Kit is and why you need one. Well, the main purpose of the MagnetFrame Kit is to hold the garment in place tightly until your embroidery machine is done punching out the design. The secret is all in the MagStik “technology” — the magnets produce an invisible magnetic force that locks ANY type of garment in place making it tighter and easier to embroider on. It’s especially good for hard-to-hoop areas, like, collars, cuffs, pockets, or sleeves. But, like with any good technology, the MagFrame’s application extends well beyond that. This kit allows you to embroider on large-scale items like towels, totes, or on the back of a jacket. How to Install the MagnetFrame Kit on Your Embroidery Machine: Next comes the fun part — it’s time for some hands on action! You’ll need to learn how to install the kit on your embroidery machine. Keep in mind that the following instructions are a demonstration for the kit that fits the 1202C, since it has additional parts. However, with the purchase of the MagnetFrame Kit for the 1201C, you also receive the necessary parts for the 1501C installation. You may find that you can skip some of these steps if you’ve purchased the MagnetFrame Kit for the Avance 1501C machine only. So, let’s get started! Step 1: Remove Screws from the Brackets Using a 3mm Allen Key For the first step, you want to start with the left and right brackets also referred to as the arms in these instructions. Put them down in front of you, then take a 3mm allen key and remove the screws from each bracket. Step 2: Fasten the Brackets to the Pantograph or Bracket Connect Plate Having taken out the screws from the brackets, the second step is to fasten the brackets to the pantograph, or bracket connect plate. The way it works is simple. You see, the brackets have a slot mechanism — you simply slide the bracket connect plate into these slots and lock them in place with screws. But, you want to ensure that you place the brackets in the right place on the plate. We chose to place the right bracket in the third and fourth hole. For the left bracket, we positioned it into the sliding mechanism making sure the screws are NOT over-tightened. You want to make sure that the right bracket has enough room to move around freely for the next step. Step 3: Add the U-Frame to the Left and Right Brackets Now you are ready for the third step! In this step, you need to screw on the correct grip ears and add the U-Frame to the left and right brackets. Depending on which kit you bought will determine which ears you will use. Note: The 1201C kit will come with BOTH sets of grip ears, one for the 1201C (15.5″ ears) and one for the 1501C (14″ ears). However, the MagnetFrame Kit for the 1501C will only come with its corresponding grip ears. In the video above, the 15.5″ grip ears are already screwed onto the U-Frame. After the grip ears are screwed on, it’s time to add the U-Frame to the brackets. Grab the U-Frame and slide the left bracket over until it lines up with the left grip ear. Snap the grip ear into place under the clip on the bracket. It should clip right into the first hole. Then tighten the loose screws onto the bracket connect plate. Next, snap the right grip ear into place under the clip on the right bracket, as you did with the other side to ensure that the U-Frame fits. Next, remove the U-Frame again by sliding it out from the clips so that we can install the bracket connect plate to the machine. Step 4: Install the MagnetFrame on Your Embroidery Machine To finish this off, the last step is to install the MagnetFrame on your Avance embroidery machine. Remove the old pantograph plate from the machine by twisting the two black thumb screws on the machine. Then lift the entire plate right off. Save the black thumb screws for the installation of the new bracket connect plate. Next, slide the new bracket connect plate into the same spot on the embroidery machine. Make sure to line up the holes on the bracket connect plate with the pegs on the machine. On the left side of the bracket connect plate, there are two holes. The left peg on the machine should sit in the second hole of the plate. On the right side, there are four holes. The right peg on the machine should sit on the first hole. After it’s set correctly on the pegs, twist the thumbscrews back on to tighten everything up. See full instructions and buy the MagnetFrame Kit here - https://colmanandcompany.com/blog/202...