DJI Neo and Insta360 Go 3 / 3S Action Camera Mount - Works in ALL Flight Modes скачать в хорошем качестве

DJI Neo and Insta360 Go 3 / 3S Action Camera Mount - Works in ALL Flight Modes

We now also have a Neo bottom mount available here: Website: https://bit.ly/djineomount Etsy: https://www.etsy.com/listing/1809717070 https://www.ebay.com/itm/205096921239 Get the Top DJI Neo Action Camera Mount Here: Our Website: https://bit.ly/neomount Etsy: https://www.etsy.com/listing/1798688848 eBay: https://www.ebay.com/itm/205055443244 Get the Insta360 Go 3S Camera Here: https://amzn.to/4dVIFkQ Get the DJI Neo Duct Guards Here: 2 Color Version: https://bit.ly/neoduct2c Solid Color Version: https://bit.ly/neoduct Get the DJI Neo AirTag Mount Here: Our Website: https://bit.ly/neoairtag Etsy: https://www.etsy.com/listing/1796392130 eBay: https://www.ebay.com/itm/205046603558 PLEASE NOTE: Normally the Neo has 20-24 satellites locked with the camera mounted but not recording. Just like most 4K cameras when you start recording on the Go 3S the satellite count can drop slightly due to RF interference the camera produces. You should still get 14-16 satellites, still plenty to get a 3D Fix. After you start recording on the camera if you lose 3D fix just wait 30 to 60 seconds and your satellite count should recover. DO NOT fly the Neo at night with any type of payload, it will not fly well without the use of vision sensors using the remote. Be sure to thoroughly test in an open area at close range prior to serious use. Product Information: Action camera mount for the DJI Neo (camera not included). This mount works with any camera with full size GoPro style fingers, a camera weighing 40g or less is recommended. When using the Insta360 Go 3 or 3S the NEO flies well in all flight modes including FOLLOW ME, Remote Control, Phone Control, FPV and Manual modes. This mount is a 3D Printed 2-Part TPU and PETG action camera mount for the DJI NEO drone. The mounting fingers are TPU which helps dampen vibrations from the drone virtually eliminating all Jello and micro jitters in video recordings. The lower portion of the mount is made of PETG for secure attachment to the drone. No tools or other hardware are required to install the mount on the drone. The included 4mm hex wrench is only used to install the bolt that holds the camera to the mount. The nut and bolt are made of Polycarbonate which is a fraction of the weight of a steel nut and bolt. Product Info: Weight (without Go 3 Holder): 11 Grams Weight (with Go 3 Holder): 15 Grams Material: 3D Printed PETG and TPU Nut / Bolt: M5 Polycarbonate Wrench: 4mm Hex There are two different purchase options available: Camera Mount without Insta360 Go 3 / Go 3S holder. Camera Mount with Insta360 Go 3 / Go 3S holder. The DJI Neo and Camera shown in the photos are not included, this listing is for the 3D printed mount only. INSTALLATION INSTRUCTIONS: Simply clip the front hooks over the front ducts, then clip the back hooks over the rear ducts. Use the included hex wrench to install your action camera that has full size GoPro style fingers. *Disclaimer - Aerial-Pixel will not be held responsible for the use and/or misuse of this product. Any damages to equipment or bodily damage are solely the responsibility of the purchaser.* Timestamps: 0:00 Intro 1:00 Mount Installation 1:40 About the Mount 3:00 Works in ALL Flight Modes 3:27 Hand Launching 4:52 Follow Me Flight Example 6:35 Recap Some of the links above may be affiliate links, purchasing from these links don't cost you anything additional but help out the channel tremendously! Thank you for your support! #insta360 #insta360go3s #insta360go3