Mosky Audio Bright Flame Guitar Amp & Cab Sim Demo скачать в хорошем качестве

Mosky Audio Bright Flame Guitar Amp & Cab Sim Demo

Here's a quick demo of the Mosky Audio Bright Flame Zero Watt Amplifier and Cabinet Simulator, clearly inspired by the DSM & Humboldt Simplifier range. Product Description A Zero watt stereo amplifier that will fit in your pedalboard and replace a full amplifier signal chain, achieving unprecedented analog realism thanks to its stereo mic’d cabinet simulation, stereo FX loop, tube-like power amp stage, and a full featured clean preamp based on 3 classic amps. Controls and Switches: Preamp Section: Amp model: Selects between 3 classic amplifiers: AC BRIT: Classic AC30 sparkly and three-dimensional sound. A true British heritage since the 60's. AMERICAN:Classic blackface deluxe sound. Sweet and dynamic with a balanced response. By far the most used amp on studio recordings MS BRIT: Classic clean-to-crunch vintage plexi style amp. The sound that defined rock music. Gain: Sets the gain of the selected amp model. Level: Sets the preamp master volume level. Tonestack: The tone stack on the Simplifier is a genuine configurable three band classic amplifier topology, keeping the same feel, response and interaction of the original amp. High: Controls the high frequency band Mids: Controls the mid band (AC Brit 500Hz, American 450Hz, MS Brit 650Hz) Lows: Controls the low end frequencies. Power amp section: This stage is an accurate approximation of the interaction between the power tubes, output transformer and global feedback, which produces a particular frequency response for different tubes and speakers. PRESENCE: Controls the hi-mids response just like the feedback based presence control on tube amps. Turn it up to cut through the mix or turn it down to sweeten aggressive distortions. RESONANCE: Controls the low-end and resonance peak caused by transformer-speaker interaction in tube amps. Now you can control the dampening factor and get super tight lowend clarity and authority. POWER TUBES SECTION: 3 way toggle switch that mimic the different response of classic tube types: EL34: Complex mid response with a compressed feel. 6L6: A more open and dynamic response with deeper bass and sparkling highs. KT88: Similar to 6L6 but with improved low end range, perfect for bass or 7+ string Guitars. Stereo Cabsim: MIC POSITION: Controls that responds like a real CENTER/OFF AXIS microphone position adjusting the precise amount of high-end roll off you look for. As usual with real mics and speakers, placing the MIC outside the center works best for distorted tones, and cleans sound best near the center. Cab Style Switch: 1x12: Open Back combo with vintage speakers that emphasize the high mids (2-4 Khz), great for cutting through the mix without too much low end mud. 4X12 : Huge sounding resonant low end cabinet with modern speakers, great for rock and heavier tones with sparkly high end, and in-your-face lows. 2x12 : Warm and well rounded open back combo, with rich mids ( 1-3 KHz) and creamy high end. Other Switches and Controls: SPREAD CONTROL: This unique feature allows you to create a pseudo stereo imaging, by delaying certain frequencies (like a phaser effect). It will make your sound bigger and 3 dimensional, even if you are using a mono configuration. GND LIFT: Disconnects the ground connection from the XLR out. Use in case you are getting hum problems when connecting to an external device. TRS OUTPUTS : Each TRS output has a switch beneath them. You can use them if you want to use a different amplifier in parallel, or use the signal to record the guitar without the effects, for later reamp on the DAW. RIGHT OUTPUT SWITCH: OUT R: Same as XLR RIGHT OUT, in this mode you have the overall signal chain coming from the RIGHT CABSIM of the Simplifier. SUM MONO: This mode blends both channels of the Simplifier and turns into a Mono output. Very useful when you’re sending full stereo signal thru the XLR outputs and need a mono signal to add another device (mono monitor or single amp for example) without losing one of the channels if you’re using both CabSims from FX Return. LEFT OUTPUT SWITCH: OUT L: Same as in XLR LEFT OUT in this mode you have the overall signal chain coming from the RIGHT CABSIM of the Simplifier. THRU: This output Bypasses completely the Simplifier taking your signal straight from the PreAmp Input. Very useful for ReAmping purposes or just to take your pedals “in-front” right to the input of your amp whilst can approach all other 3 outputs (2 x XLR + RIGHT TRS OUTPUT) to your preferred devices as PA System, Audio Interfaces, FRFR Monitor, etc. Headphone Level: Controls the volume on the headphone output. Technical Specs Current consumption: 50mA to 100mA (if Headphone out is used) Supply voltage: 9V - 12V Polarity: Center negative Input impedance: 1 Meg Ohm TRS output impedance: 100 Ohm DI Output impedance: 120 Ohm Send output impedance 100 Ohm Return Input Impedance: 1 Meg ohm Headphone Power : 120mW @ 32 Ohm Dimensions: Width : 122 mm Height: 64 mm Depth: 73 mm Weight: 422 g