etrailer | What to Know About the License Plate and Tail Light Relocation Kit for Yakima EXO System скачать в хорошем качестве

etrailer | What to Know About the License Plate and Tail Light Relocation Kit for Yakima EXO System

Click for more info and reviews of this Yakima Hitch Bike Racks,Hitch Cargo Carrier Bag,Roof Basket,Ski and Snowboard Racks,Trailer Hitch: https://www.etrailer.com/Accessories-... Check out some similar Hitch Bike Racks,Hitch Cargo Carrier Bag,Roof Basket,Ski and Snowboard Racks,Trailer Hitch options: https://www.etrailer.com/dept-pg-Acce... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-review-ya... Hi everyone, it's Evangeline here at etrailer. And today, we're looking at the Yakima taillight and license plate relocation kit for the Yakima EXO system, otherwise known as Yakima LitKit here at etrailer. Now, when you do have the Yakima EXO system on your vehicle and on your hitch, you will notice that the accessories, especially when you have the top shelf installed, can be pretty large and bulky, so you may cover your license plate and or your taillights with everything assembled and installed and mounted to your hitch. So, because of that, we do have the Yakima LitKit, which is the taillight and license plate relocation kit. That way, you can stay safe and legal on the road. What you get with this kit are two taillight brackets, so they go onto the arms of your SwingBase. And you have these red taillights as well as this license plate light for your license plate. So, just make sure to maybe get either an extra license plate or to move your license plate from the back of your vehicle to the front. And when you do take your EXO system off, you won't forget to put it back on your car. So, this includes a wiring harness to connect to your vehicle. So, what you need to do is just make sure that one, you have a wiring harness already pre-installed on your vehicle, and it just uses a four-way wiring harness. So, if you do happen to have a seven-way port, just pick up a seven-way to four-way adopter here at etrailer. This fits US and Canadian license plates. Those are the ones with the holes on the top for these two plastic bolts. So, if you do happen to have a different style of a license plate, you may need to drill a hole into the top of it, so that this will fit. So, these LED lights are going to mimic the taillights on your vehicle. So, whether you have your brakes on, or whether you have your turn signal on, so you're left as well as your right, this is gonna help keep you safe and legal on the road. You can also see, with the flashers on, how bright they are. So, this is gonna be great, especially during emergency situations, when you need to keep your hazard lights on. Now, as for ground clearance, the lowest point of the LitKit is gonna be your license plate. So, with the standard size of a license plate, it's gonna sit five inches below the bottom of your SwingBase arms to the bottom of that license plate. So, the install process is very simple. It's just a bolt-on process and it includes the wrench you need to tighten those bolts down, so let's take a look at that process. So, now we have all our parts here set up for assembly. I already put together the passenger's side bracket, so we can put together the driver's side bracket together. So, first, line up your bracket with the bolts in the back, and then fit your wiring through the middle, then you're gonna put a bolt through the front. So, just fit that through and then use a flat washer, and then a nut to hold that down. Tighten down both bolts with the included tool. After you have your brackets assembled, you're then gonna open up the arms on the SwingBase to install them onto the arms, so just pull that lever on the side and swing out those arms. Now, you're gonna line up the bracket with your arms on your SwingBase. So, depending on which accessory you have is gonna be what holes you're gonna use. So, most of your accessories will use back two holes, but if you do happen to use the EXO DoubleUp bike rack, you're gonna use the front two holes. So, I'm gonna put them on the back two holes and use the included knobs, just to put them into place, and then tighten them down. Now, if your Yakima EXO accessory covers your license plate, this also has a license plate relocation bracket. So, what you can do is you can use the included plastic screws as well as the plastic nuts, and that goes in the back. And then just use a screwdriver or you can just use your hands to tighten this down here in the back, and that will relocate your license plate. And then you're almost there to the wiring harness, but first, you need us to set up the clips. You're gonna have six clips and that's gonna be three on each side. So, just pop them into the holes on the bracket, and make sure you have all six securely installed. And now, you get to plug in your main wiring harness. So, here's the plug-in port, right here towards the front of t