SMT: Mounting proximity switch скачать в хорошем качестве

SMT: Mounting proximity switch

00:00 Mounting proximity switch Mounting the proximity switch SMT-8M to a standards-based cylinder. This video shows the instructions at the following products as an example: proximity switch SMT-8M-A-PS-24V-E-2,5-OE, series 01-2020:13, NO: normally open, parts number 574335 standards-based cylinder DSBC-U-32-100-PA-N3, series D408, parts number 1463250 The 8M clamping principle or the 10M clamping principle is also suitable for the following proximity switches: with 8M or T-slot: SMT-8M-A-… SMT-8M-… SME-8M-… SMAT-8M-… CRSMT-8M-… SDBT-BSW-… SDBT-MS-…EX6 SIES-8M-… SAMH-S-… SDAS-MHS-… SDAT-MHS-… with 10M round groove or C-slot: SMT-10M-… SME-10M-… - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Further information and helpful links - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Instructions SMT-8M-A-...-24V-E-... https://www.festo.com/sp/8082624 Instructions SMT-8M-A-PNS/PSO-24V-E-... https://www.festo.com/sp/8046150 - - - Instructions SME-8M-...-24V-... https://www.festo.com/sp/8112709 - - - Festo spare parts catalogue More information about the product, tightening torques, dimensions and spare parts https://www.festo.com/spareparts - - - Festo Support Portal for all further information https://www.festo.com/sp - - - Festo online catalogue https://www.festo.com/catalogue/smt - - - Festo website https://www.festo.com - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Safety instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - All guidelines, regulations and specifications applicable in the country in which you are located must be complied with before, during and after carrying out this work. Only qualified specialized personnel who have undergone training and instruction are permitted to install, repair and commission the equipment; such work must be carried out in accordance with the operating instructions for the products concerned. All equipment must always be switched off before commencing maintenance and repair work. All power supplies must be permanently disconnected. Some protective devices are taken out of operation during maintenance and repair work. They must be properly reinstalled and put back into operation immediately after the work has finished, and their correct functioning must be checked. Prior to starting work you must read and understand the safety instructions and the instructions for handling the product in full. You must also ensure compliance with these instructions at all times whilst carrying out your work. No liability whatsoever shall be accepted for damage caused by noncompliance. Although every care has been taken when drafting these instructions, Festo SE & Co. KG does not accept any liability for any errors they may contain or the consequences of such errors. Likewise, no liability is accepted for direct or consequential damage resulting from incorrect use of the products and tools. Compliance with the applicable regulations governing occupational safety, safety engineering and interference suppression, as well as the stipulations contained in these operating instructions, is a mandatory requirement when working with the products. The General Terms and Conditions of Festo SE & Co. KG, which can be viewed on the Festo website (www.festo.com), also apply. Should you have any questions or concerns, please contact Festo SE & Co. KG directly. Do not start work until these questions or concerns have been clarified. #Festo #proximityswitch #SMT #sensor