Whitestone Install *Tips and Tricks* The BEST Screen Protector скачать в хорошем качестве

Whitestone Install *Tips and Tricks* The BEST Screen Protector

Warning: As seen in the video at the 10:26 mark it is very important as a beginner that you make sure the surface is level (Use a physical bubble level and have business cards nearby) and leave the alignment bars (Plastic L Shapes) on during the curing process with the UV light, otherwise the screen protector may slide off of the phone. I was doing this for a friend at his house with the table he had, therefor as you saw at the 10:26 mark it began to slide away. Me doing so many installations I was use to this sort of thing happening, and quickly corrected the issue. I find the alignment bars to get in my way when moving the screen to the most case friendly position. However when I started out I did use these alignment bars, think of them as training wheels. Just be sure when you manually align the screen protector that the alignment bars are not lifting out of their 3 bumps and that they are not lifting your screen. Make sure your surface is level otherwise the adhesive could pour over the edges of the phone. Business cards help immensely, along with not working on installation in the middle of a 2 piece table. This is how to install the Whitestone screen protector on the Galaxy S8/S8+ along with Tips and Tricks to get the installation perfect every time. I have installed over 200 of these at work and have found my method to come out perfect every time. You will need to have about 2 hours available to do this install, an hour for install if you are new and an hour for it to cure. You also can not apply a case for 24 hours after installation. Installation 1.) Clean the phone using 1 alcohol wipe, use 1 cloth wipe to clean 2.) Set phone inside the tray using the engraved Speaker and Button for proper alignment 3.) Place the black connector inside the other tray 4.) Place the top tray on top of the bottom tray using the engraved speaker and button words as navigation 5.) Uncap the larger glue stick lid and place it in the black connector on the top tray 6.) Have business cards on the side for standby and leveling 7.) Slowly release the samller top cap until you see a little glue come out 8.) Keep an eye on the glue to make sure its not going to pour over the edge 9.) Use business cards to level out the opposite of where the liquid glue may be tilting 10.) Repeat 7- 9 until cap is completely off the glue stick 11.) Leave glue stick inserted with no cap for 60 seconds 12.) Lift the tray above phone and lightly tap the glue stick to make sure no glue is remaining careful not to touch the glue on the phone with the tray 13.) Move the tray to an area away from the phone and remove the inserted glue stick and cap both ends to avoid any messes 14.) Add the 2 plastic L pieces to the 3 raised bumps on the left of the phone 15.) Insert the guide into the blue ribbon on the right side of the phone, careful not to touch the glue it will spill over if you do 16.) Check for any dust that may have build up using your dust remover 17.) Remove the plastic protector over the glass screen protector careful not to touch the glass by using the edges and making sure the curves face down 18.)Make sure the cutout for the speaker in the screen protector are facing the right direction 19.) Tilt the left side of the screen protector down and insert it away from the glue and into the L plastic alignment pieces and lay it onto the paper guide 20.) Slide the glass up and down to make sure is properly placed 21.) Slowly remove the guide as soon as you see the glue make contact with the screen protector, remove the paper guide quickly 22.) Make sure the screen protector is barely below the camera and is in line with the speaker, it should have a small gap below the camera to where the protector is not on top or touching the protector 23.) Blast the top part with the UV light and wait till it turns off 24.) Blast the bottom part with the UV light and wait till it turns off 25.) Repeat 23 and 24 26.) Using the second alcohol wipe clean the phone front and back as the back may have some excess glue 27.) Use the second cloth scree wipe to clean the screen protector and back, set aside the cloth as it will be covered in glue, be careful not to touch the glue on the edges underneath the screen protector 28.) Blast it with UV light on the top again 29.) Blast it with UV light on the bottom again 30.) Now clean the screen protector using the last alcohol wipe and cloth, you can keep this cloth as it won't have glue on it if you cleaned everything thoroughly in step 26 31.) Leave your phone to set for one hour 32.) Enjoy your new Whitestone screen protector =] Please wait 24 hours before you apply a case to the phone