Rc F1 Boat with Real Outboard Motor Mercury Racing 360 full 3d print скачать в хорошем качестве

Rc F1 Boat with Real Outboard Motor Mercury Racing 360 full 3d print

STL file https://cults3d.com/:2254330 ####Mercury Racing 360 Outboard Engine### -This outboard has a height of 20cm -Suitable for hulls above 70cm, I will make many hulls that fit this outboard Engine! so you can make lots of rc boats with just one engine -I used a 3670 motor, this outboard can use motors up to 4076 (not tested yet). -this outboard can adjust trim position on mounting and and can be adjusted the height from hull -gear lubricant hole for easier to fill the lubricant after playing -easy to print without any support and pre orianted -need 400grams of filament (pla) used abs for motor mounting -have a great watercooling system Print Setting: -min print area = 200x140x50 -nozzle = 0.4 -layer hight = 0.15 lower is better for high quality -perimater = 5 wall line -top/bottom = 5 -infill = 30% -support = no BOM: -bevel gear shaft 4mm 15t 0.8 2pcs ( https://a.aliexpress.com/_opczqfU ) -bearing 604zz 1 pcs ( https://a.aliexpress.com/_oCFW9Pv ) bearing 684zz 5pcs ( https://a.aliexpress.com/_oCFW9Pv ) shaft 4mm 30cm rigid couple joint 4x5 (depending on the motor you use) ( https://a.aliexpress.com/_oDoRGWb ) -drive dog 4mm ( https://a.aliexpress.com/_okQpmtp ) -propeller up to 50mm (i use 40mm diamter) (https://a.aliexpress.com/_olAepaR ) -brushless motor up to 4076 ( i used 3670 2150kv) heat insert m2.5 (2.5IDx3Lx3.5OD) 18pcs ( https://a.aliexpress.com/_olfvCxz ) m2.5x5 18 pcs ( https://a.aliexpress.com/_oEKdBSR ) -m3 x35/40 2pcs with nut (for adjustable trim position) -m2x3 self taping screw (for gear lubricant hole) -push rod connector 2pcs for servo rod ( https://a.aliexpress.com/_olInPFh ) ####F1 Hull PowerBoat#### -70cm length -Nice desain and performance -easy to build and print withoutsupport -have a pin joint for each body to make easier to put it together -need 1.300gram of pla Print Setting: -Min print area = 235x235x230 -nozzle = 0.4 -layer hight = 0.2 lower is better for high quality -perimater = 2/3 wall line -top/bottom = 4 -infill = 15% -support = only servo mount BOM -m3x8mm 16pcs for battrey tray, esc tray, servo mount, and servo -m3x25mm 4pcs and nut 4pcs for outboard mount -m3x40mm 3pcs and nut 3pcs for cover -Push rod or stainless stell Leader Fishing wire for servo rod Electronic that i used -Battrey 2pcs lippo 2s 5000mah -Esc Flycolor 150a -Servo 25kg waterproof -dumborg 6ch transmitter 3D PRINTING SETTINGS 3d printer fdm -nozzle = 0.4 -layer hight = 0.2 lower is better for high quality -perimater = 4 wall line -top /bottom = 4 -infill = 30% -support = no #f1 #outboard #mercury #rcboat #diy #3dprinting #3dmodeling #f1h2o #rc #casting