FINALLY FINISHED: 3UZ V8-SWAPPED FRS w/ Stock Trans скачать в хорошем качестве

FINALLY FINISHED: 3UZ V8-SWAPPED FRS w/ Stock Trans

Link ECU Helped us get to the finish-line with the 3UZ-FE VVTI V8 powered FRS BR-Z GT-86 Build, and we can't thank them enough! Here is where you can pick up the Plug and Play FRS BRZ GT-86 ECU 241-4200 on our website: https://collinsperformancetechnologie... Link G4X Used with Oprahbuilt PnP Harness: https://collinsperformancetechnologie... Links to the Full Kit, Power Steering Delete, Shifter, Connector Kit Etc: -https://collinsperformancetechnologie... -https://collinsperformancetechnologie... -https://collinsperformancetechnologie... We can't thank the people that helped out on this video enough: -Andrew and George at Link ECU North America -Eric Coxe at Suncoast automotive specialists -Tyson Flores [email protected] for Link G5 based Wiring harnesses Plug and Play(minus 4 wires switched at the ECU area, he might have a Patch harness by the time this video launches) -Robert and Jessica Stothart Oprahbuilt.com for all of the Link G4X Plug and Play harnesses/ECU's and He's coming out with an OEM+ Almost PnP Harness to the AC1 AC2 AB1 Plugs by Summer 2026ish also he does remote tuning too. "Disclaimer: The content provided in this video is for educational and informational purposes only. We are not factory-trained or certified automotive technicians, and the information shared here is gathered freely from publicly available sources on the internet. By watching this video, you acknowledge and agree that any actions you take based on the information provided are done at your own risk. The creator(s) of this content shall not be held liable for any damages, injuries, or losses that may result from the use or misuse of the information presented. Always consult with a qualified professional before attempting any repairs, modifications, or procedures on your vehicle. By continuing to view or using this content, you agree to hold harmless the video creator(s) from any and all liability." This video was a very difficult undertaking and it took many many months and soooo much money to put together in a coherent manner that makes sense for everyone. with all of that said we are launching our Patreon page to help continue long builds like this to the finishline, our Patreon page is :   / collinsgarage   When you subscribe monthly to our page you get detailed wiring spreadsheets and insider information on how-to properly setup the OEM+ portion of this harness/ECU system. The OEM plus wiring and starting/functionality was a massive undertaking and it was difficult to say the very least. We could make a complete other video alone simply detailing out just the wiring for that system. With that said we will give away some cliff notes of what you have to do in order to start this 3UZFE SC430 modified ECU inside the FRS Chassis using the FRS ECU A B C D connectors along with the Gauge cluster Wiring, but for the full spreadsheet of all of the connectors, all of the information to make your own harness, cut sheet for all of the lengths etc hit our Patreon page and start your monthly subscription as this won't be the last long detailed video series that we do. Here are just some of the things you need to do to get the FRS to work correctly for the swap: FRS Chassis/Fuse Relay box will not power up unless you supply an accessory(key on) Ground (-) going to the A35-13 wire on the "B" connector of the OEM FRS ECU connector. This is crucial and powers up the main EFI relays, Fuel Pump relay inside the relay box (Pass Side Fender well area). Without an external relayed grounding source going to this wire, we weren't able to power up even the Link ECU or Fuel Pump, Fans, Etc. This held us up for days until we figured it out. FRS Chassis Fuel pump bypass for OEM+ ECU solution ONLY(Do NOT do this for any Standalone or Link ECU based systems). On the Passenger side(USDM), rear seat, upper plastic area, there is a plastic interior panel where the rear passenger's right arm would rest. Behind this plastic panel there is a 6-wire Pulse width modulated Fuel pump controller(factory) and a 6-wire harness in a vertical orientation. You need to jumper the two end wires (thicker gauge wires) These are the positive wires, that need a fuse between them(for safety), in order to send Key-on 12v+ to the fuel pump when using the OEM+ ECU solution. this could also be controlled by the Lexus ECU if you run an external, ground controlled relay from the Lexus SC430 2001-2004 ECU "B14" wire, then send 87 (12v+) to the Thick Red wire on the FRS Chassis Fuel pump controller wiring harness. Thank you For watching, please like and subscribe for more content!