BMW E30 Front Struts Restoration | BMW E30 325i Sport Restoration S1 E1 скачать в хорошем качестве

BMW E30 Front Struts Restoration | BMW E30 325i Sport Restoration S1 E1

Get 2 months of Skillshare for FREE using this link: https://skl.sh/restore Episode 1 of the BMW E30 325i project Car Restoration. In this Episode, I show my progress so far with the project and complete the restoration of the front Struts for the BMW E30. If you would like to send me something to restore, tools to use or anything to support Restore It, please send to: Restore It Mail Box PO Box 50 CHATTERIS PE16 9AZ Subscribe for Weekly content! Tools & equpitment used: Quartz Lacquer - https://goo.gl/8PTVKM Base Coat Paint - https://goo.gl/mWhufG Rust Remover - https://goo.gl/13gopW Moldex Full Face Mask - https://goo.gl/NNYGrv FGL 5 Spray gun - https://goo.gl/Acg5rd A.N.I. R150-T Mini Spray gun - https://goo.gl/cHTJS2 Colad Washable Overalls - https://goo.gl/3Css9E Colad Mixing Cups - https://goo.gl/8DYmE8 Colad TurboMix Sticks - https://goo.gl/cYZfks Colad Synthetic Paint Strainers - https://goo.gl/H79ZgL Steel wire bits - http://geni.us/keyaD Rotary Tool - http://geni.us/HGed Concentrate Degreaser - http://geni.us/yUn9 Mannesmann Socket Set - http://geni.us/HCDZ In this episode, I bring you up to date with the progress on my E30 that I started two years ago. Due to time and money constraints, I haven't done any work on it in quite a while. That is about to change! Any parts I have already restored before I started YT will be purchased and done again just for you guys. That includes an engine! Firstly I removed the struts from the car. As I mentioned in the video, the yellow springs are the wrong springs for this car. Someone sent me the wrong ones. So, compressing them was vital as they jacked the car up by about 3 inches and had a lot of pressure built up. Once they were compressed safely I began removing the top mounts, spring mounts, rubbers, discs and protection plates. I needed to put the strut assembly back on the car so I could more easily remove the hub nuts, hubs and cups. I needed to use some heat to loosen one of the nuts and then a puller to remove both hubs. Once everything else was off the struts, it was time to remove the shock absorbers themselves. This took a lot of time as the nuts were completely stuck. Once removed you could see how worn they actually were. Along with many other parts. Parts that I decide to replace later on. After straightening a few cable mounts on the struts, it was time to blast them to remove any paint and rust. I then had to weld a hole that was on the bottom of one of the struts and used a belt sander to remove any weld splatter from either me or the factory. It was then time to etch, prime, sand, paint and lacquer the struts. Once all of the new parts had arrived it was time to reassemble the struts with the new parts. Luckily I didn't have to compress the new springs as they were so much shorter than what was in there. I wasn't and still aren't 100% sure what I do with those big long rubbers if I have the dust tubes and bump stops in, they only fit on top of the bump stops, not over. If someone knows if and how they fit in, I would appreciate it if you left it down in the comments. Once I was happy to leave it as it was, I tightened the spring down using a digital torque wrench adaptor. Once the disc protection plates and cups were back on, it was back on the car to attach the new hubs. Firstly I had to attach the hubs to the discs to be able to get them on the strut shafts more easily. This was still very difficult. I found pushing the hub on a little and then pulling it off, leave the race behind meant that I could then thread the old nut on and center the race, then whack the hub and disc on knowing it's going on straight. It was then a few twists with the impact gun to tighten everything up. I'm waiting for a more power torque wrench to arrive to tighten those to the correct specs. Finally, I had to push two top caps onto the top of the strut assembly. This proved to be the most stressful part of the restoration, they just didn't want to go in. A small amount of heat and they were in. The restoration was complete. Thanks for watching! Disclaimer: I am no professional. I am completely self-taught and would appreciate any feedback, advice or constructive criticism. I don't add music to these videos so that you can choose to listen to what you like if you would like to. #BMW #E30 #Restoration Become a patron to win the Items featured in these videos! Patreon -   / restoreit   PayPal Donations - [email protected] - If you would like to help towards more tools and projects. Follow me on Social media to keep up to date with videos and giveaways. Twitter -   / restore__it   Facebook-   / restoreitcha.  . Instagram - @RestoreItChannel Patreon -   / restoreit   Discord - I now also have a discord server if you want to chill with like-minded people and maybe learn something new. -   / discord