How to make a cardboard Gingerbread Man Costume скачать в хорошем качестве

How to make a cardboard Gingerbread Man Costume

Make a cardboard Gingerbread man costume it is so easy you don't even need a template, watch the video and head to the blog for more details on how to put it together. https://www.zygotebrowndesigns.com/po... Check out heaps more cardboard costumes at www.zygotebrowndesigns.com The gingerbread man costume is so easy to make that no template is needed. It's a simple concept and quick and easy to make. The materials used: Cardboard (Single Walled 2-5mm thick) (I used an old Nerf gun box that I had left over, it was perfect because the tone of the cardboard matched my sons Pj's. ) Single faced cardboard. (Had this cardboard in the house from a larger parcel, but you can buy this from any craft store. OR you can just use some normal single walled cardboard and score it on one side, so as it can be moulded around the outside for the circle head.) Craft knife https://amzn.to/3X4Zsvb Scissors https://amzn.to/3ThKilj Sticky tape White paint pen or white paint and paint brush https://amzn.to/4cPYkBB Glue Gun https://amzn.to/3MlT9i9 Glue sticks https://amzn.to/3Xfe8rE Beige Nylons/stocking https://amzn.to/3TgjiT4 Beige Pyjamas or any matching beige top and bottom. (We picked up some PJ's in a Kmart sale for $6 AUD which were perfect, however have found a similar set on Amazon https://amzn.to/3MuB6q7). The above affiliate links are to amazon products we currently use for making cardboard costumes. (they may differ from the video) but please use whatever is available, these are suggestions. Steps involved; HEAD: Watch the below video to see how easy it is. using a large bowl, trace around the outside circumference to make TWO perfect shaped circles. ( I used a bowl that had a diameter of 28cm/11inches) Carefully cut out the circles using a craft blade. Draw on your Gingerbread face design. ( I traced around a small tin to make sure the eyes were nice and round.) Carefully cut out your facial features using a craft blade. Turn your circle over (so as the back of the face is facing up) and cut your beige nylons /stockings into 3 pieces to fit over the eyes and mouth of the gingerbread persons face. Using hot glue, dap some along the top of one of the eyes and attach one side of the nylon stocking to the top part of the glue dabbing the nylon into the glue (I actually use a low melt gun and am very careful not to burn my fingers while doing this part. You can also put a bandaid over your finger to protect it or use a small piece of cardboard to dab down the nylon stocking into the glue.) Apply more glue at the bottom of the eye and stretch the nylon stocking down to cover the eye hole and dab it into the glue. You will need to do this to the sides of the eye as well to make sure the whole eye hole is cover with the nylon/stocking. Repeat this process with the other eye and mouth. Turn the Gingerbread face over and paint/draw your gingerbread face on using a paint pen or paint. Cut some single faced cardboard long enough fit around the gingerbread face circle with an opening at the bottom for the head and wide enough to fit a head in. (I used 21.5cm/8.5inches wide and 67.5cm/26.5inches long of single face cardboard, with the fluting channels running along the width.) Glue the single faced cardboard around the back of the gingerbread persons face trying to keep the edging flush with each other. Then glue the back of the head on the same way. HANDS Using the some single faced cardboard (or scored cardboard) fold it in half and trace out the around your hand (as seen below and in the video). Cut around your outline (making sure to keep the fold connection intact.). Open up your folded hand and glue the sides down. I used sticky tape to keep the side connected and so I could mould the cardboard to fit a hand in it. Draw/paint your hand design onto the front and back of the cardboard. I used another sheet of single face cardboard around the cuff of the wrist however you could always just make a longer mitt. Cut a thumb hole. Music: Hyperfun by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. https://creativecommons.org/licenses/... Source: http://incompetech.com/music/royalty-... Artist: http://incompetech.com/ Safety Your safety when creating our fantastic costumes is very important and it's very important to exercise caution when working with hot glue, sharp blades and not to mention cardboard can be sharp too. Please follow all safety precautions for the materials you use to ensure a safe and enjoyable crafting experience. As we really want you to enjoy the process without injury! Please note that Zygote Brown Designs is not liable for any injuries that may occur during the creation or use of our costumes. It's the responsibility of the user to take proper safety precautions and to use the materials in a safe and responsible manner.