How to reassemble the steering column on a 1967 Chevy Camaro for Beginners скачать в хорошем качестве

How to reassemble the steering column on a 1967 Chevy Camaro for Beginners

After disassembling two steering columns, stripping them down, and painting them, I was able to reassemble one. This is by far one of the most detailed videos I've ever made, and it's also the first video I have ever done with a voice over. With that in mind, check out this video to see how I reassembled the steering column on a 1967 Chevy Camaro! Subtitles * Subtitles are available in this video "Use the Closed Caption button to turn them on or off" Project Redemption * Episode Twenty-Eight - Steering Column P3 Episode Subtitle ----- How to reassemble the steering column on a 1967 Chevy Camaro for Beginners Video Speed ---------- 300x to 500x Started Recording ---- 04/23/2022 Finished Recording --- 04/23/2022 Chapters * 00:00 Video Intro 00:10 Let the unwrapping begin 00:45 Using a Heat shrink tube as a replacement for the Column Crush Cover 01:37 Inserting the Inner Plastic Bearing to Guide the Shifter Tube 01:47 Installing the Shifter Bowl on the Upper portion of the Steering Column 02:15 Inserting the Washer, Spring and Lower Bearing into the Steering Column 02:32 Installing the Lower Shifter Cover onto the Steering Column 02:37 Installing the Lower Rubber Firewall Boot and an Aftermarket External Boot 02:56 Adding Lithium Grease and Installing the Tolerance Ring kit on the Steering Shaft 03:06 Inserting the Steering Shaft into the Steering Column 03:12 Getting Ready to Install the Upper Steering Wheel Housing 03:14 Attaching the Upper Steering Column Bearing to the Turn Signal Assembly 03:30 Inserting the Assembly into the Housing while trying to neatly route the Wires 04:14 Installing the Screw to hold the assembly together along with the springs and lock plate 05:12 The Assembly is now ready to be installed into the Steering Column 05:16 Installing the Assembly and routing the harness while locking the unit down by twisting in place 05:28 Now that the Assembly is locked in place I will Tightening the screws down 05:30 Just in case I Added Some Lithium Grease to the Upper Bearing 05:54 Installing the Wave Washer, Thrust Washer, and the Retaining Ring on the Steering Shaft 06:12 Making Sure that the Retaining Ring is securely Seated 06:32 Double Check the Shaft to make sure that it spins freely 06:36 Installing the Harness Wire Covers and Clips on the Steering Column 06:42 Installing the Steering Column to Dash Bracket 07:02 Adding washers and Tightening the Steering Column to Dash Bracket down 07:17 Taking a Closer Look at the Steering Column Fully Assembled 07:27 Please Subscribe if you want to see more videos like this, Thanks for watching! Subscribe *    / @gogogarage   Shout Out * Go Go Garage wants to Thank those for their Support! Please check out; @aMAYSing Metal Works    / amaysingmetalworks   Products * Most of the Steering components were purchased here; https://www.heartbeatcitycamaro.com/ Software * Audacity Affinity Photo Filmora Version Pro Gear * DJI Osmo Pocket OnePlus 5 Android Phone Canon 5D Mark IV Camera Shure MV7X XLR Podcast Microphone Focusrite Scarlett Solo 3rd Gen ♫ Music ♫ 1983-SynthWave-RetroWave-by-RetroWave-Kingdom © Music provided by DreamWave Kingdom © Watch the original movie here:    • 1983 SynthWave RetroWave [ No Copyright FR...   Production * Go Go Garage All Rights Reserved 2021-2022 Hashtags * #gogogarage #gogogarageclub #camaro #67Camaro #67camarorestoration #projectredemption