Kent Bathroom Water Softener Regeneration Guide | Salt Recharge & Aquasol Hardness Test Kit Demo скачать в хорошем качестве

Kent Bathroom Water Softener Regeneration Guide | Salt Recharge & Aquasol Hardness Test Kit Demo

👉 Aquasol Water Hardness Test Kit Buy Link: https://amzn.to/4pRWIyp 👉 Kent Water Softener Buy Link: https://amzn.to/3LbwM1H Kent Bathroom Water Softener Regeneration Guide Salt Recharge & Aquasol Hardness Test Kit Demo (Complete Step-by-Step) INTRODUCTION Hard water can silently damage your bathroom fittings, geyser, tiles, taps, and even your skin and hair. If you’ve installed a Kent Bathroom Water Softener, congratulations—you’ve taken the right first step. But here’s the truth most people don’t talk about: 👉 A water softener only works well if you regenerate it correctly and on time. In today’s detailed video, I’ll show you: The exact Kent water softener regeneration process How to recharge it using the correct kent water softener regeneration salt And finally, how to test water hardness before and after regeneration using the Aquasol Hardness Test Kit This is a complete DIY guide, no plumber required. So let’s get started. WHAT IS KENT WATER SOFTENER REGENERATION? Kent water sofener regeneration process is the method of cleaning and recharging the resin beads inside the softener using salt. In simple words: The resin beads trap calcium & magnesium Over time, they get exhausted Regeneration flushes them clean using salt water (brine) Softener becomes as good as new again Without regeneration, your Kent water softener becomes just a plastic tank with no real benefit. HOW OFTEN SHOULD YOU DO KENT WATER SOFTENER REGENERATION? This depends on: Water hardness level Number of bathrooms Daily water usage General guideline: Hard water (300+ ppm): Every 7 -10 days We’ll later verify this using the Aquasol hardness test kit. TOOLS & MATERIAL REQUIRED Before starting, make sure you have: Kent Bathroom Water Softener Kent water softener regeneration salt Also known as rock salt or crystal salt Food-grade, non-iodized salt Aquasol Hardness Test Kit Clean water Measuring cup or mug Gloves (optional but recommended) STEP-BY-STEP: KENT WATER SOFTENER REGENERATION PROCESS Now let’s get into the actual kent water sofener regeneration process. STEP 1: Switch Off Water Supply Turn OFF the inlet water valve Make sure no water is flowing through the softener This prevents pressure issues during regeneration. STEP 2: Open the Salt Chamber Locate the salt container on your Kent water softener Open the lid carefully You may see: Old salt residue Water level inside the tank That’s completely normal. STEP 3: Add Kent Water Softener Regeneration Salt Now comes the most important step. How much salt to add? Typically 500g to 1kg per regeneration Refer to your Kent model manual Slowly pour the kent water softener regeneration salt into the chamber. STEP 4: Add Water (If Required) Some Kent models require adding water manually. Add clean tap water Enough to dissolve salt and create brine The brine solution is what regenerates the resin beads. STEP 5: Start Regeneration Mode Depending on your model: Turn the regeneration knob Or rotate the valve to “Regeneration” Or press the manual regeneration switch The kent water sofener regeneration process usually takes: ⏱️ 10 mins During this time: Salt water flows through resin Hardness minerals are flushed out Waste water goes to drain STEP 6: Flush & Rinse Cycle After regeneration: Softener automatically rinses resin Excess salt is removed System resets to softening mode Wait until the process is fully complete. STEP 7: Resume Normal Water Supply Turn ON the inlet valve Run water for 2–3 minutes Discard initial water Your softener is now recharged. HOW TO CHECK IF REGENERATION WORKED? (IMPORTANT) Never assume regeneration worked. Always test the water hardness. This is where the Aquasol Hardness Test Kit comes in. AQUASOL HARDNESS TEST KIT – COMPLETE DEMO Let’s now do a before and after hardness test. What is Aquasol Hardness Test Kit? The aquasol hardness test kit is a simple DIY water testing solution that measures: Total hardness in ppm Calcium & magnesium presence It’s widely used for: Home testing RO input testing Water softener efficiency check ARD WATER TEST – BEFORE REGENERATION Step 1: Collect water sample directly from bathroom tap Step 2: Fill vial up to marked level Step 3: Add Aquasol reagent drops one by one Shake gently after each drop Step 4: Observe color change Each drop = specific ppm hardness. 👉 In most homes, you’ll see: 300–600 ppm (hard to very hard water) HARD WATER TEST – AFTER REGENERATION Now repeat the same process after regeneration. Using the aquasol hardness test kit, you should see: Dramatic color change Reduced number of drops Hardness around 50–100 ppm That confirms your kent water sofener regeneration process was successful. Kent Bathroom Water Softener Connection with Gas Geyser and Hand Shower:    • Kent Hard Water Softener Gas Geyser Hand S...