🔧❄️ LIVE: H2S Cold-Garage Fix — 150% Mega Starfish • Clean, Calibrate, 2 Walls • 15h Restart скачать в хорошем качестве

🔧❄️ LIVE: H2S Cold-Garage Fix — 150% Mega Starfish • Clean, Calibrate, 2 Walls • 15h Restart

🔧❄️ Troubleshooting and relaunching my first large-scale 150% articulating “Lucy Longlegs” starfish on the Bambu H2S, printing outside in a cold Michigan garage. A few areas flaked off the build plate, so I’m doing a full cleanup, running Vision Encoder build-plate calibration, adjusting the slice from 3 walls down to 2 (as per the original model), adding light adhesive, and restarting the ~15-hour print. MODEL LINK I’ll pin the exact MakerWorld model link in chat at start. WHAT HAPPENED • Plate flaking on long legs during the cold-garage run • Likely combo: low surface energy + drafts + aggressive first-layer cooling • Extra wall count may have added shrink stress at edges TODAY’S PLAN (live) 1) Remove failed sections safely (cool plate → flex → trim brim/zits) 2) Plate prep: warm water + mild dish soap, rinse, dry, then 99% IPA wipe while warm 3) Vision Encoder (optical) plate calibration routine 4) Slicer updates: • Walls: 3 → 2 (match original; reduce edge stress; keep 4–5 top/bottom) • First-layer width 120%, flow 105–110%, fan OFF on L1, ON from L3 • Brim 5–8 mm around outer legs; seam away from hinges • Bed +5 °C for the first 3 layers; nozzle +5 °C on L1 if needed 5) Adhesive (light): PVA glue-stick or Magigoo skim coat only after calibration 6) Cold-garage protocol: • Preheat bed/enclosure 10–15 min; block drafts • Keep filament dry; swap AMS desiccant; short pre-purge before long spans 7) Restart the job (~15h) and monitor: • First-layer macro cam • Brim integrity, corners, hinge islands • Time-to-finish updates every few hours SETTINGS SNAPSHOT (PLA baseline) • Layer height: 0.20 mm (top skins 0.16 mm optional) • Walls: 2 • Top/Bottom: 4–5 • Infill: 12–18% • Bed: 60–65 °C (first 3 layers at higher end), Nozzle: 200–210 °C • Cooling: L1 fan 0%, L2 low, normal from L3 • Brim: 5–8 mm; Draft Shield optional if garage is breezy • AMS-II Pro: group colors to minimize swaps; purge short test before long legs RUNTIME TARGETS (approx) 00:00 — Recap, pin model link, show flaked zones 00:08 — Plate cleaning + prep 00:18 — Vision Encoder calibration walk-through 00:30 — Slicer changes (2 walls, brim, first-layer tweaks) 00:45 — Adhesive skim coat; preheat soak 00:55 — Launch 15h restart; first-layer watch 01:20 — Brim/corners audit; hinge island check 03:00 — Cold-garage temp/draft check; status update 08:00 — Mid-run QC: seam placement, leg stability 14:30 — Final hour prep; cool-down plan; gentle articulation demo (if time) PINNED CHAT (copy/paste) • Model link: [pinned above] • Fix recipe: clean plate → Vision Encoder calibration → 2 walls → brim 5–8 mm → fan off L1 → bed +5 °C first 3 layers → light adhesive • Cold-garage: preheat, block drafts, keep filament dry • Alt aspect ratio stream link will be posted if I go horizontal later SAFETY Hot surfaces and moving axes. Let the part fully cool before removal or flexing. Don’t force tight hinges—micro-deburr first. CALLS TO ACTION Like • Subscribe • Comment “PROFILE” for my H2S cold-garage starfish preset • Share your best first-layer tricks CONNECT YouTube:    / @starfishinnovations   Facebook: https://www.facebook.com/profile.php?...