Level cutting machine er lintel work running in savar, DEPZ, Dhaka with construction chemical point скачать в хорошем качестве

Level cutting machine er lintel work running in savar, DEPZ, Dhaka with construction chemical point

Construction work running for ready to production area in level factory. Name: " CONMIX TILE JOINT FILLER - TJF " It is a dry pre mix, waterproof cement based tile joint filler for internal and external use, available in a variety of colours, for wall and floor tiling " CONMIX TILE JOINT FILLER - TJF " TJF is a dry pre mix, waterproof cement based tile joint filler For internal and external use Available in a variety of colours In Grade ‘A’ joints upto 5mm and in Grade ‘B’ joints from 5-12 mm For wall and floor tiling Multi featured tile grout TECHNICAL DATA: Composition : White Portland Cement, special fillers, non-fading pigments and chemical improving agents including powder polymers Binder : White Portland Cement Aggregate Size : 0.1 mm for Type A, 0.2 mm for Type B Appearance : Powder available in different colours Mixing Ratio : Type A : 8.5 ltrs of water per 25 kg bag Water/Powder ratio = 0.34 Type B : 8 ltrs of water per 25 kg bag Water/Powder Ratio = 0.3 Approx. YieldnCoverage Type A 18.5 ltrs per 25 kg bag; Type B 18 ltrs per 25 kg bag Coverage depends on tile size Density * : Wet : 1.8 kgltr Dry : 1.7 kg/ltr Compressive Strength * : 22 /mm2 28 days Flexural Strength : 3.0 /mm2 28 days Pack Size : 2 kg plastic pouch Shelf Life : 12 months from date of production when stored under dry conditions Working Time : Approx. 30 minutes Curing : 48 hours by potable water Specification : BS5385-1, ANSI118.6, DIN:18156 BACKGROUND The tile joints must be clean, free of dust deposits and other contaminations which may affect the adhesion. The suction in the background should be neutralized by applying potable water. There should be no free water in the joints to be grouted as this could lead to de-bonding MIXIN: TJF supplied in 25 kg bags must be mixed with potable water only, in a clean, non-corrosive, uncontaminated receptacle. To ensure a homogeneous and uniform mix, an electric agitator must be used The amount of water to be added is: 8.5 ltrs per 25 kg bag approximately 34 by weigh For TJF - Type A. 8 ltrs per 25 kg bag approximately 32 by weight For TJF - Type B.The amount of water added should be constant for every batch Add TJF to water, turn the contents of the bag carefully adding small amounts at a time into the receptacle. Stir frequently and mix again before applying No further water should be added to mix The mixed mortar must be used within 30 minutes Hard and set mortar should not be re-mixed or used APPLICATION METHOD: Conmix TJF is to be applied within the tile joints using a rubber spatula Taking care to ensure that the grout is well compacted into the joints. The excess material on the surface of the tile should be removed using a dry cloth. The grouting should be carried out in accordance to the relevant standards and code of practice. Conmix demonstration team will assist in these procedures upon request. SPECIAL NOTES: Grouting should commence only after the tile glue / adhesive has dried out completely. The applied Tile Joint Filler should be properly cured. STORAGE: Conmix TJF must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale