Will the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs Fit Your 2016 Nissan Versa? скачать в хорошем качестве

Will the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs Fit Your 2016 Nissan Versa?

Click for more info and reviews of this Rhino Rack Roof Rack: https://www.etrailer.com/Accessories-... Check out some similar Roof Rack options: https://www.etrailer.com/fitguideroof... Search for other popular Nissan Versa parts and accessories: https://www.etrailer.com/vehicle/2016... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-review-rh... Today on our 2016 Nissan Versa we'll be doing a test fit on the Rhino Rack Vortex Aero roof rack system using part numbers RRVA118B-2 for the aero crossbars and part number RRRLKVA for the leg kit and part number DK232 for the custom fit kit for our Versa. To begin our test fit you'll notice that we've already got the front one installed. We're going to do the rear one together. Let's go ahead and start by grabbing our leg, okay Then we'll grab our pad. Now on the bottom here you'll notice that it's got this raised portion here. We want to make sure that this facing inward as you see it here. We'll just push it in place. Okay. Once that's installed then we can install the hook. Let's go ahead and take this bolt out here. Now you also want to refer to your fit guide and make sure you have the correct hook because they are different from the front to back. We'll set it in place and then we'll loosely install the bolt. Just like that. Okay. We can set that down. Let's go ahead and remove our end cap on our crossbar. We can actually turn it upside down. We need to make sure that our plate here is loose so we can easily slide it on. Just like that. While we're at it we can actually go ahead and replace that end cap. Now, according to our fit guide, we'll need to be 142 millimeters from this point here to the first portion of our leg. Ordinarily, you're going to get these little plastic strips with measurements on them to help you get that, but for demonstration purposes, we're going to grab our tape here and we're going to be looking for 14.2 centimeters because that what ... that's what it . excuse me, that's what it converts to. That's going to be right about there. It actually looks pretty close, so if that comes off just clip it back in place. Then we'll tighten that down with our included tool. It doesn't need to be extremely tight. Just enough to flatten out our little walk washer there. Okay. Now we've already got the other side set so let's go ahead and open up our rear doors. Then we'll set it in the general area, which is going to be right around here. You want to be sure and set it gently in place. All right. Then we can grab our tape and we'll refer to our fit guide and we're actually looking for 700 millimeters, but in centimeters it converts to 70 centimeters. We're going to come back . excuse me that's going to be from the center of our front cross bar to the center of the rear. We're pretty close. With that side being lined up I'm going to go ahead and line up the other. Close here. All right. That looks pretty good. Now you'll want to be sure, as I put the pad on here, that it's going to be nice and snug up against this channel here. Now if it's not, you'll need to change it around, so for this side I've actually got it on . We're going to go ahead and switch it around. Just a little mistake. Set that back in place. There. As you can see it's going to fit just inside the channel. Just like that. Make sure that measurement's right real quick and then we can go ahead and tighten them down. All right. Good. We'll grab our included tool and we want to tighten it down just enough to where it makes contact first and that goes for both sides. You don't want to start tightening down too much because it'll pull the whole crossbar to one side. That's not what we want. Do the same thing over here. Since we know that that side is already making contact we can go ahead and give this a few more turns and start tightening it up. Now it's a good idea to alternate. We want our tool here that's got a little arch in it, we want it to be straight when we tighten it and that's how we know we've got the correct torque on it. Be sure to do that for both sides. All right. Then we can put on our locking covers. These are just going to clip in like so. All right. Now before we finish up here the front installs very similar. We followed our fit guide. We started from our fixed point and we went forward. Got the center here and then to get the back we measured from center of the crossbar and that's how we got it. It's a very easy installation. You want to be sure to lock up your end caps and then you're all set. That's going to complete our test fit on the Rhino Rack Vortex Aero roof rack system on our 2016 Nissan Versa.