У нас вы можете посмотреть бесплатно Universal Joints - Part 6: Proper U-Joint Installation или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса ClipSaver.ru
Weber State University (WSU) - Automotive Technology Department - Transmission Lab. This is the sixth in a series of videos on universal joints, constant velocity joints, and driveshafts. In this episode, we learn how to properly install universal joints. Timeline: 0:00 Start 2:45 the contents of a new GM universal joint 7:00 Instructions to center the universal joint and set the axial endplay 7:22 Yoke inspection 9:55 Line bore inspection 13:47 Precautions to take when removing driveshaft from vehicle 15:55 Direction of grease Zerk installation 23:45 Preparing to install the universal joint into the slip yoke 24:14 Three tools needed to install a universal joint bearing cap 25:30 Why using a Vise can cause universal joint damage 27:15 Setup the Yoke and universal joint cross for installation 28:24 Pressing the first bearing cap 29:10 Orientation of bearing cup during installation 29:21 Setup the yoke for the second bearing cup installation 30:55 Axial end play example 31:25 Preparing to install a snap ring 34:45 installing one copper-colored snap ring 35:55 preparing to install the opposide snap ring 37:45 Copper-colored snap ring not fitting 38:58 Adjusting the cross and bearing cup positions to remove endplay 42:00 Why selectable thickness snap rings are needed 44:00 Installing thinner snap rings 47:47 Removed universal joint to inspect again 48:28 Measuring cross-width variation 50:42 Cleaning the yoke again 52:00 Universal joint reinstalled in the yoke 54:35 installing the universal joint into the aluminum driveshaft This video series helps partially cover the following NATEF Master Tasks: 3.D.1. Diagnose constant-velocity (CV) joint noise and vibration concerns; determine necessary action. 3.D.2. Diagnose universal joint noise and vibration concerns; perform necessary action. 3.D.4. Inspect, service, and replace shafts, yokes, boots, and universal/CV joints. 3.D.5. Check shaft balance and phasing; measure shaft runout; measure and adjust driveline angles. 3.E.4. Measure drive axle flange runout and shaft end play; determine necessary action. Questions for teachers: 1. How many different thicknesses of snap rings came in the GM universal joint kit? 2. Why would someone want to perform a yoke line bore inspection? 3. In which direction should a grease Zerk face when installing a universal joint? 4. What three tools are needed to install a universal joint bearing cap 5. In which direction should a bearing cap always face when handling and installing it? 6. Look at timeframe 30:55. Describe axial endplay in your own words 7. Why did the second copper snap ring not fit in the slip yoke snap ring groove? 8. What thickness of snap rings finally fit in the grooves of the slip yoke? 9. How much cross width variation did the universal joint in this video have? 10. What color of snap rings were installed on the driveshaft side of the universal joint? Subscribe to the weberauto Youtube channel for more great videos. / weberauto Visit the following website for information on how to attend our school and obtain an associate's degree or bachelor's degree in Automotive Technology. http://www.weber.edu/automotive This video was created and edited by Professor John D. Kelly at WSU. For a full biography, see http://www.weber.edu/automotive/J_Kel...