• ClipSaver
ClipSaver
Русские видео
  • Смешные видео
  • Приколы
  • Обзоры
  • Новости
  • Тесты
  • Спорт
  • Любовь
  • Музыка
  • Разное
Сейчас в тренде
  • Фейгин лайф
  • Три кота
  • Самвел адамян
  • А4 ютуб
  • скачать бит
  • гитара с нуля
Иностранные видео
  • Funny Babies
  • Funny Sports
  • Funny Animals
  • Funny Pranks
  • Funny Magic
  • Funny Vines
  • Funny Virals
  • Funny K-Pop

How to cut steampipe/black pipe for a turbo merge collector with simple tools скачать в хорошем качестве

How to cut steampipe/black pipe for a turbo merge collector with simple tools 7 лет назад

скачать видео

скачать mp3

скачать mp4

поделиться

телефон с камерой

телефон с видео

бесплатно

загрузить,

Не удается загрузить Youtube-плеер. Проверьте блокировку Youtube в вашей сети.
Повторяем попытку...
How to cut steampipe/black pipe for a turbo merge collector with simple tools
  • Поделиться ВК
  • Поделиться в ОК
  •  
  •  


Скачать видео с ютуб по ссылке или смотреть без блокировок на сайте: How to cut steampipe/black pipe for a turbo merge collector with simple tools в качестве 4k

У нас вы можете посмотреть бесплатно How to cut steampipe/black pipe for a turbo merge collector with simple tools или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:

  • Информация по загрузке:

Скачать mp3 с ютуба отдельным файлом. Бесплатный рингтон How to cut steampipe/black pipe for a turbo merge collector with simple tools в формате MP3:


Если кнопки скачивания не загрузились НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу страницы.
Спасибо за использование сервиса ClipSaver.ru



How to cut steampipe/black pipe for a turbo merge collector with simple tools

A friend decided to build a new turbo manifold out of steam pipe/black pipe/nominal bore pipe and asked me to give him a hand with it, our first attempt at cutting the merge collector pipes didn't work very well so I came up with this method. "This video is intended for entertainment purposes only" The pipes were cut longer than required to allow trimming later, and as square as possible on the end that will locate against the stop. A thick cutting disc was used at first to get a flatter cut but it took forever to cut and the disc had to be thrown out after cutting two pipes as it wasn't cutting anymore. Thin discs cut much faster, last/work longer and can be made to cut fairly straight with care. A 9" grinder might work better but not many people own them (and probably fewer people should) so I didn't try using one. The jig should be made as rigid as possible, but something thrown together like this gives reasonable results. The symmetrical cuts are for turbochargers with square or round (V-band) inlets. The offset cuts are for turbochargers with rectangular turbine inlets. Trimming the entry to match the turbo flange would probably be better done with a grinder sled and flat board. This method will work for any practical incidence angle, a similar method of angle determination could be used for bandsaws, mills and drop saws. For a given number of primary pipes the alignment angle (90 degrees in this video) will be 360/number of primaries.

Comments

Контактный email для правообладателей: [email protected] © 2017 - 2025

Отказ от ответственности - Disclaimer Правообладателям - DMCA Условия использования сайта - TOS



Карта сайта 1 Карта сайта 2 Карта сайта 3 Карта сайта 4 Карта сайта 5