Install: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2018 Toyota Sienna скачать в хорошем качестве

Install: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2018 Toyota Sienna

Click for more info and reviews of this Tekonsha Custom Fit Vehicle Wiring: https://www.etrailer.com/Custom-Fit-V... Check out some similar Custom Fit Vehicle Wiring options: https://www.etrailer.com/fitguidet1.htm Search for other popular Toyota Sienna parts and accessories: https://www.etrailer.com/vehicle/2018... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-t... Ryan: Hey everybody, Ryan here at etrailer.com. Today on our 2018 Toyota Sienna we're going to be taking a look at and showing you how to install the Tekonsha T-One Vehicle Wiring Harness.This kit is going to provide your trailer with the proper lighting functions as you're pulling it down the road. Not only keep you safe, but legal.Now, one thing I really like about this wiring kit, and what kind of separates from some of the others, is that it's going to use a module box. What that's going to do is protect your factory wiring, and for short we're going to cur on the trailer. Now it comes with a heavy duty dust cap which will help keep your terminals protected and corrosion free. If you want to go a step further I'd recommend every now and again putting some dielectric grease on them.Now our wiring is going to have a power output of 2.1 amps per circuit for our stop and turn signals, and 7.5 amps per circuit for our tail lights. So what that means, this is going to provide us with plenty of power to run any kind of light we have on our trailer. Whether it be an incandescent bulb, or an LED.Now the way we got our wiring from inside the van to outside to our trailer we'll just pull it out of our storage compartment and drop it over the threshold. Now anywhere on the threshold is fine. It's not going to damage your wire as long as you stay away from the latch. Then whenever you're done using your wiring you can store it inside to keep it out of the elements and out of site.Now, some of our customers said during the installation they had some issues with the power wire being too short. Well, I'll show you some tricks in how I ran our power wire up to the front and it gave us plenty of length. Speaking of which, let's go ahead and wire it all up together now.To begin our installation we're first going to need to remove our tail lights. So we'll go ahead and open up our hatch. To get our tail light out we're going to need to remove two 10 millimeter bolts. Once those are out we can take our tail light and just wiggle it very gently to kind of help free it by pulling it towards us. If it doesn't want to pop out I'll show you a trick to get it out. Back in this area there's going to be a little tab that's an alignment pin that's holding it up. So what I'm going to do is just take the palm of your hand, push it forward like that. Then we're able to disconnect our electrical. To do that there's going to be a tab here in the center. Push down, pull out. You can set it to the side. Repeat that same process for the passenger one.Now we're going to remove our rear threshold. To do that we're going to have three hooks with fasteners underneath them. One here, here and here. To get our fasteners out you're going to want to lift the hook up, then take a small flat head kind of lift behind this piece of plastic. If you hold that up you'll see at 10 millimeter bolt that we need to remove. You can do that same thing for the other two remaining fasteners.Now once those fasteners are removed we can grab the bottom of our threshold and kind of pull it up and away. Then kind of work it from the top by pulling up. This are the tabs that we're holding our threshold into place. Now once we have it out we can set it off to the side.Now we're going to pull back our side panel here to get some room to work behind our tail light. We we'll grab it at the bottom and just gently work it out to release our tabs. Same thing over here on the passenger side with the exception of removing our jack storage compartment door. Push our tab in, pull it off, then we can work that panel out. Now on the passenger side we can take our new wiring and module box, and we'll take the box and lift our panel back just kind of slide it through like this. Then we're going to take the ends that have the green and white wire, and the red and brown wire and we're going to feed them up through here into the opening where our factory tail light wiring goes through.So here's the opening where our new wiring came through. Now we're going to plug these in to the factory wiring. So what we'll do is take one end and clip it in. Now you can't get these mixed up because the plugs are a little bit different. So no matter which way you go you can't get it wrong. Now we're going to take our yellow wire with the connectors on it and run it over to the driver's side. We're going to