Epson M1120 wireless network setup Wi-Fi Direct Mode Setup Wi-Fi Protected Setup (WPS) скачать в хорошем качестве

Epson M1120 wireless network setup Wi-Fi Direct Mode Setup Wi-Fi Protected Setup (WPS)

Epson M1120 wireless network setup Wi-Fi Direct Mode Setup Enabling Wi-Fi Direct Mode Wi-Fi Direct Mode Setup You can set up your product to communicate directly with your computer or another device without requiring a wireless router or access point. In Wi-Fi Direct Mode, the product itself acts as a network access point for up to 4 devices. Enabling Wi-Fi Direct Mode You can enable Wi-Fi Direct mode to allow direct communication between your product and computer or other devices without a wireless router or access point. Make sure paper is loaded before you begin. Note: If you are printing from a computer, make sure you installed the network software as described on the Start Here sheet. 1. Hold down the Wi-Fi button and press the network status button until the Wi-Fi light and WiFi Direct light flash alternately. Then release both buttons. After both lights stop flashing, the Wi-Fi Direct light remains on. 2. Hold down the network status button until the power light flashes to print a network status sheet. 3. Use your computer or wireless device to select the Wi-Fi network name (SSID) and password listed in the Wi-Fi Direct section of the network status sheet. 4. If you are connecting an Android device, the Wi-Fi and Wi-Fi Direct lights flash simultaneously. Do one of the following: • Press the Wi-Fi button to connect the device. • Press the stop button to cancel the connection request. You should now be able to print to your product directly from your computer or device. If you cannot print successfully, repeat the process above and make sure you enter the password exactly as written on the network status sheet. Wi-Fi Protected Setup (WPS) If your network uses a WPS-enabled wireless router or access point, you can quickly connect your product to the network using Wi-Fi Protected Setup (WPS). Note: To check if your router is WPS-enabled, look for a button labeled WPS on your router or access point. If there is no hardware button, there may be a virtual WPS button in the software for the device. Check your network product documentation for details. Using WPS to Connect to a Network If you have a WPS-enabled router or access point, you can use Wi-Fi Protected Setup (WPS) to connect your device to the network. Note: To check if your router is WPS-enabled, look for a button labeled WPS on your router or access point. If there is no hardware button, there may be a virtual WPS button in the software for the device. Check your network product documentation for details. 1. Press the WPS button on your router or access point. 2. Hold down the Wi-Fi button on your product for about five seconds until the Wi-Fi light and WiFi Direct light flash alternately. The Wi-Fi light turns green to indicate a successful connection. Note: Be sure to press and hold the Wi-Fi button on your product within 2 minutes of pressing the WPS button on your router or access point. Printing a Network Status Sheet You can print a network status sheet to help you determine the causes of any problems you may have using your product on a network. To print the status sheet, hold down the network status button on the product for at least five seconds. Printing a Network Connection Report You can print a network connection report that provides details of the connection between the product and the wireless router. 1. To print the network connection report, press the network status button on the product. 2. Review the information contained in the report and resolve any errors. Network Connection Report Codes and Messages Error code and message Solution E1 Confirm that the network cable is connected and network devices such as hub, router, or access point are turned on. E2, E3, or E7 No wireless network names (SSID) found. Confirm that the router/access point is turned on and the wireless network (SSID) is set up correctly. Contact your network administrator for assistance. No wireless network names (SSID) found. Confirm that the wireless network name (SSID) of the PC you wish to connect is set up correctly. Contact your network administrator for assistance. Entered security key/password does not match the one set for your router/access point. Confirm security key/password. Contact your network administrator for assistance. E5 Security mode (e.g. WEP, WPA) does not match the current setting of the printer. Confirm security mode. Contact your network administrator for assistance. E6 MAC address of your printer may be filtered. Check whether your router/access point has restrictions such as MAC address filtering. See the documentation of the router/access point or contact your network administrator for assistance. E8 Incorrect IP address is assigned to the printer. Confirm IP address setup of the network device (hub, router, or access point). Contact your network administrator for assistance. E9 Confirm the connection and network setup of the PC or other device.