У нас вы можете посмотреть бесплатно EndoT800's Neca Combat 18" Endoskeleton Custom или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса ClipSaver.ru
Follow me for the latest projects at / endot800mods / john.conner.7731247 This is my Neca 18" ver.1 Endoskeleton Custom. This is the completed project. This Endo has some great potential for customizing. It has size & its relatively cheap plus there's plenty of them out there to be had. First up was to take it apart and change and improve some of the Endo's parts where needed rather than just doing a simple repaint. I wanted to incorporate more metal parts to give it a better overall finished look. I ended up doing a lot more fabricating work to many of the Endo's parts which is making a nice improvement overall. I started with the head. The first change was the eyes. They are too oversized, bright and have poor circular shapes. I removed the existing eye lenses and used some brass tubing to make a housing for the new lenses. They are now smaller & more circular. Next was up was to reshape the hands and feet. As you can see, the hands are need of reshaping. For each hand, I started with scratch piece of aluminum for the base. I cut and reshaped the wrist base, then polished and drill the necessary holes for the fingers, rods and screws. I ended up cutting the original fingers at each joint and creating new a new set of fingers using the same joints and using brass & stainless steel rods. I then used tiny screws to attach each hand to the arm. I then finished up each hand by adding the additional finishing stainless steel metal parts. For the feet, I essentially did the same as with the hands. I took them completely apart and added metal shaped piston rods and reinforced them with stainless steel rods. Next was to refinish the Phased plasma gun in-the-40 watt range. I covered the seam that runs in the middle of the gun so it looks like one piece rather than two. I then drilled out each barrel and then apply primer for painting. Now I wanted to correct the pistons for the pelvis area on the front and back. I ended up taking apart each piston and cutting and replacing the shafts using brass rods and remounting the pistons so it matches closer to the original Endo. For each leg, I made the two cut outs to each of the side of the leg so they are now open. The look much better now and match up closer to the original Endo design. For the chest piston mounts, I used some special metal screws to mount all the pistons in place. I then made the base from scratch. I added plenty of victims with their skull fragments scattered about. The Endo should feel right at home with this environment. This was a total repaint from scratch. Once the painting was complete, I finished modifying the hands & arms with stainless steel cables & metal parts. All the exposed screw holes are now sealed. The upper pistons are now secured by polished metal & brass screws. The phased Plasma gun in the 40 watt range was refinished & painted with a little added heat distortion to the barrel tip. I replaced the plastic shoulder cables with real stainless steel cables and scratch made the head cable connector; I then rerouted and connected them to polished brass mounts. I left some of the brass parts in their natural color, mainly to give the Endo a little variance in color. The polished brass parts actually look quite nice against the chrome. I then gave the overall chrome finish a slight worn look rather than just a fully nice chrome finish. As I said before this Endoskeleton doesn't get much love, but with some tweaks & mods it now holds its own to most of the Endo statue's out there plus for about $40 bucks you can't go wrong. Enjoy!