Vespa Moped Carburetor Cleaning скачать в хорошем качестве

Vespa Moped Carburetor Cleaning

You can support the channel by purchasing moped merch here: https://shop.mopedrich.com/ Link to article: http://www.mopedrich.com/vespa-moped-... Here is a short video for cleaning a Dellorto SHA 12:10, 12:12, or 13:13 Vespa moped carburetor.  Most Dellorto SHA carburetors are similar to the Vespa style carburetors, so these steps can be used on those as well. The video can be found below, and screen shots are provided if wanting to read and follow along. Here is the dirty 12:12 Delloroto SHA on my custom Vespa moped build coming soon. The moped was running with the carburetor like this but I wanted to clean it up as I was installing some new parts and tuning the moped. A tip before starting is to find a clean working surface that if gas or carburetor cleaner splashes, you won't mind.  I do not recommend cleaning a carburetor on a dining room table or in doors.  The gas and carburetor cleaner will produce fumes.  I used a small portable work bench table top like this Keter Folding Compact Workbench (https://amzn.to/2P6IEA6) and a baking cookie sheet.  It is made of metal and holds up to the gas and cleaner.  It also helps keep the parts together and from rolling off the table or shop gremlins from getting parts. With an 8 mm socket or wrench, remove the bolt that holds the fuel inlet.  There should be a screen that is used to trap debris when gas is flowing. Next remove the two screws holding the fuel bowl onto the carburetor.  After the bowl is removed, remove the brass main jet.   Using something with point and solid, press on one side of the float needle to push it out a bit. Unless the carburetor is really gunked up it should not need much pressure. Using some needle nose plies, remove the pin completely.  Tip: use your hand to keep the pin from flying out and getting lost.  Take the carburetor cleaner (I use this https://amzn.to/2KOOvXy) attache the supplied straw and spray it through the fuel passage.  Carb cleaner is compressed so be careful it might splash back and into your face/eyes. Then where the brass jet screws into the carburetor, stick the carb cleaner straw and spray that passage way. With the cleaner spay any dirt or debris around the carburetor to clean hard to reach areas. Spray the brass jet as well to make sure it is not clogged, you may need to replace the jet if the cleaner cannot unblock the jet passage. Take the bowl and wipe it down with a rag.  Then spray the hard to reach areas with the carburetor cleaner.  Again be careful it will splash back at you.  Wipe it down once again with a rag.  With the cleaner spray the fuel inlet and wipe down it down with a rag. Then spray the screen clean of any debris that could be blocking fuel flow.  Tip: slide or hold the screen with needle nose pliers to not get carburetor cleaner on your hands.  The cleaner could irritate your skin.   Finally reverse the beginning steps to reassemble the carburetor. Vespa Grande moped, Vespa ciao moped, Vespa si moped, Vespa bravo moped Carburetor cleaning. The process I take to clean the carburetor of the batavus moped with a Vespa grande subframe and engine. While doing some tuning to the Batavus Vespa custom moped, I made this video to show how to clean the Carburetor on most Vespa Mopeds. This will work for Dellorto 12:10, Dellorto 12:12, Dellorto, Dellorto 13:13 SHA Carburetors. Clone SHA 13:13 or 12:12 Carburetors are built the same so this would be the same for those as well. I did not change any of the gaskets on the carburetor because they were not leaking, but it is probably recommended to change the gaskets on the bowl and fuel inlet.    • LAKEY INSPIRED - The Process