How To Install A Fahren Tap скачать в хорошем качестве

How To Install A Fahren Tap

Installation STEP 1 Before installing the 4-1 instant boiling water tap it is essential to thoroughly flush through the supply pipes in order to remove any impurities from your system. Failure to carry out this simple procedure could cause problems or damage. We strongly recommend installing isolation valves to both the hot and cold feed pipes in an accessible position. This will help prevent premature failure and ease any future maintenance. All parts should be removed from their packaging and inspected prior to installation. This hot water tap requires a 35mm diameter tap hole; if replacing an existing tap, remove the old tap & clean the ends of the feed pipes using wire wool; the tap hole area should also be free from dirt and sealant. Installation STEP 3 Following the corresponding colours: 1. RED screw in the red domestic hot tail 2. BLUE screw in the blue domestic cold tail 3. GREEN screw in the silver tail with the 3/8”BSP nut on the end for the Boiling Water Tank inlet. 4. Carefully place pipes through the 35mm sink hole 5. Push the washer and securing plate over the threaded brass threaded stem tubes and secure with the two nuts (IMPORTANT Careful not to twist or pinch and pipes, it is not removable, damaged pipe cannot repair). 6. Connect the RED flexible tube to the hot water feed. 7. Blue flexible tube connect to the T piece to the cold water feed. The reducing adaptor is screwed onto the remaining end of the T piece. 8. 1⁄4” PE plastic pipe is pushed into the adaptor end and the other end pushes into the IN on the filter housing. A further 1⁄4” PE plastic pipe is then pushed into the OUT of the filter housing into a 1⁄4” push fit T piece. 9. The further two PE plastic pipes are then pushed into the T piece then go to the two brass stem tubes under the tap body using the two push fit 1⁄4” straight connectors. Installation STEP 3 1. Positioning the Boiling Water Tank unit and the filter 2. The reservoir/heater unit should be positioned on a flat level surface such that: 3. There is a minimum air-space of 150mm to each side of the reservoir/heater unit. 4. There is a minimum air-space of 25mm to the rear of the reservoir/heater unit. 5. Access to any stopcocks, valves, waste traps or other plumbing fittings that may require service is not impeded. 6. The front display and operating controls are readily accessible and visible. 7. All connection pipes can be installed without stretching or twisting of them. 8. Access to the electrical power socket to be used for this appliance is not restricted in any way. 9. There is there a fused 13A power supply within reach of the power cable, will that cable supported for its full length and not stretch. If it is necessary to extend the power cable to reach the nearest suitable socket this must be done by an electrician. 10. The filter is supplied pre-assembled to its plastic wall bracket. This should be mounted in a convenient location on a wall or cabinet side, taking into consideration the length and routing of the connecting hoses. Installation STEP 4 • Connect the 3/8“ BSP barbed connector with the silicone washer to the RED collar on the Hot water tank. Slide the clip over the silicone tube and push over the barbed connector. • Tighten the SILVER tail from the tap onto the BLUE on the Hot water tank to feel filtered cold water. • Ensure all connections are securely tightened that hoses are not stretched or kinked and that all hoses are safely supported before turning on the water supply. • Turn on the isolating valves and check for any leaks. • Pull the lever straight down and filtered water will come from the tap Installation STEP 5 DO NOT SWITCH ON THE HOT WATER TANK at the stage until the following has been carried out. • Run the FILTERED COLD WATER (NOT THE HOT BOILING WATER) for a minimum of 5 minutes to activate and clean the carbon agency inside the Anti-scaling filter before starting the Hot Water Tank. By taking this small step will prevent any carbon dust from entering the Hot Water Tank. The black coloured water is harmless and it will clear itself by running the water. • Open all installed water valves to allow water to flow to the 4-1 instant hot water tap. • Turn the spring-back hot water tap handle against its spring and hold there until the water flows from the tap spout which indicates the taps reservoir is full. • Allow the hot water handle to spring back to its rest position and check all the connections for water tightness and absence of leaks. • Any leaking joints must be tightened and the surrounding area dried before connecting the power supply. • ONLY connect the electricity supply to the Hot Water Tank at this stage. Insert the plug into the electricity socket and switch on.