etrailer | How to Set Up Your Curt Trailer Hitch Receiver on a 2006 Chrysler 300 скачать в хорошем качестве

etrailer | How to Set Up Your Curt Trailer Hitch Receiver on a 2006 Chrysler 300

Click for more info and reviews of this CURT Trailer Hitch: https://www.etrailer.com/Trailer-Hitc... Check out some similar Trailer Hitch options: https://www.etrailer.com/fitguide.htm Search for other popular Chrysler 300 parts and accessories: https://www.etrailer.com/vehicle/2006... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-t... Today on our 2006 Chrysler 300, well be installing the Curt Hitch, part number 13465. This is what our hitch will look like once it's installed. Next, well give you a couple of measurements to assist you with selecting accessories for your new hitch. In the center of the hitch pinhole to the outermost edge of the bumper, is seven inches. From the top of the receiver tube, to the ground is 10 inches. This will assist you with selecting accessories, such a drawbar, a bike rack or cargo carrier. Now, lets go ahead with the installation. First, before we can install our hitch, well need to do a little preparation work by lowering the exhaust. To do this well first put a safety strap underneath the exhaust so it can't fall any further then we need it to in order to install the hitch. Next, well go ahead and take some spray lubricant and spray down each one of the exhaust hangers that well be removing. Weve got one just above the tailpipe on both sides. One just behind the muffler on both sides and one in the exhaust pipe forward to the axle for each side. Now, weve got our hangers sprayed down well go ahead and remove each one of these exhaust hangers. With that done, we can go ahead and lower the exhaust. When removing your exhaust hangers everything you do here on the passenger side will be repeated identically on the drivers side. Now, with our exhaust lowered, we can see our attachment points. Weve got three on each side. On the driver side, our forward fastener will be a carriage bolt and block that will fish into the frame using the access hole. Then we have two well nuts that are already built-in to the frame by the manufacturer. Well be using half-inch bolts that are supplied with our install kit. Before we attempt to install our new hitch, well first take our half-inch nylon tube brush, part number 814092 and thoroughly clean the threads out of each of the well nuts with some spray lubricant. This will assist us with installing our new fasteners. With that completed, we're now ready to go ahead and install our carriage bolts and blocks using our pull wire provided with our install kit. Well feed our pull wire in through the attachment point now at the access hole. Then we can slide out our block and thread on carriage bolt. Now, well go ahead and feed both of up into the frame and pull them into position. Well go ahead and repeat the same process for the other two carriage bolt attachment points. On the passenger side, the forward two fasteners will be half-inch carriage bolts and blocks and the rearmost attachment pint will again, be a threaded well nut in the frame. Now, we're ready to go ahead and install our hitch. Well feed the hitch up above the mufflers and into position. Starting here on the drivers side, well bring our hitch up the frame and then use the flange nut to secure it. Keep in mind, it's easier to put the hitch into position, slightly on an angle to get above the rubber isolator on the exhaust hanger. Now, with our hitch secured, we can go back and use our half-inch bolts and half-inch conical tooth washers with the teeth to the washer facing the hitch and thread them into position. With all six fasteners in place, well go ahead and tighten them down. Next, well go back and torte our fasteners to specifications as indicated in the instructions. Now, with our hitch completely secured, we're ready to go ahead and reinstall the exhaust. With that done, thatll complete the installation of our Curt hitch, part number 13465 on our 2006 Chrysler 300.