How to Remove Old Mailbox Post and Replace It | Build a Custom Post скачать в хорошем качестве

How to Remove Old Mailbox Post and Replace It | Build a Custom Post

Replacing an old mailbox post can be a fairly easy task if the old post was simply found to be in soil. The task increases in difficulty if the post is mounted in concrete. Then you have much more weight and volume to dig up and remove. But it can be done: Here is a nack - use a presure washer to help you dig the old mailbox post out! Here’s a basic step-by-step guide (your circumstances may differ ) to remove the old rotted mailbox post, replicate its measurements, and build and install a new post from cedar: Tools and Materials Needed: Shovel Post hole digger (optional) Saw (hand saw or circular saw) Chisel Hammer Measuring tape Level Wood glue or exterior wood screws Cedar lumber (for the vertical post and horizontal arm) Gravel or concrete mix (optional, for stabilizing the post) Pencil Safety gear (gloves, safety glasses) Step 1: Remove the Old Mailbox Post 1. Clear the Area: Remove any objects, plants, or debris around the old post. 2. Loosen the Soil: Use a shovel to dig around the base of the old post, loosening the soil. 3.Dig Out the Post: Continue digging around the post, making a hole wide enough to get a good grip on the post. If it’s set in concrete, dig around the concrete base. 4. Remove the Post: Once the post is loosened, lift it out of the ground. If it’s stuck, use leverage (such as a 2x4) to pry it up. Step 2: Measure and Prepare for the New Post 1. Measure the Old Post: Measure the height, width, and depth of the old post, as well as the length and position of the horizontal arm. 2. Mark the Measurements: Transfer these measurements to the cedar lumber, marking where to cut and notch. Note : We chose to splice a piece green treat post that would be in contact with the soil with a cedar post that would accept paint much more readily ( to match the HOA color scheme. ) Step 3: Cut and Notch the Cedar for the New Post 1. Cut the Vertical Post: Cut the cedar lumber to the desired height for the vertical post. 2. Cut the Horizontal Arm: Cut the cedar lumber to the appropriate length for the horizontal arm. 3. Mark the Notches: Mark the areas where the vertical post and horizontal arm will intersect. The notches should be half the thickness of the wood so that when joined, they create a flush fit. 4. Cut the Notches: Use a saw to make a series of closely spaced cuts within the marked areas. Use a chisel and hammer to remove the excess wood between the cuts, creating a flat notch in both the vertical post and the horizontal arm. Test the fit by placing the arm into the notch on the post. Adjust as needed until they fit snugly. Step 4: Assemble the New Mailbox Post 1. Attach the Horizontal Arm: Apply wood glue to the notches and fit the horizontal arm into the notch on the vertical post. Secure with exterior wood screws for added stability. 2. Check for Level: Ensure the horizontal arm is level and adjust if necessary. Step 5: Install the New Post 1. Prepare the Hole: If the hole from the old post is not wide or deep enough, use a post hole digger to expand it. The hole should be about 1/3 of the post's total height. 2. Set the Post: Place the new mailbox post in the hole. Use a level to make sure it is perfectly vertical. 3.Stabilize the Post: Option 1: Pour gravel around the post and tamp it down to stabilize it. Option 2: Mix and pour concrete into the hole to secure the post. Hold the post in place until the concrete sets, or use braces to keep it steady. 4.Backfill the Hole: Once the post is secure, fill the remaining space around the post with soil, packing it down firmly. Step 6: Attach the Mailbox 1. Mount the Mailbox: Attach your mailbox to the horizontal arm following the manufacturer’s instructions or using wood screws. 2. Check for Stability: Ensure everything is securely fastened and the post is stable. Step 7: Final Touches 1. Inspect the Post: Check that the post is level and sturdy. 2. Clean Up: Remove any debris and clean up the area around the post. Your new cedar mailbox post should now be installed, looking neat and secure! All that is left is to paint or stain it to match the neighborhood ( IF you are under the thumb of the HOA ! ). :-) Thanks for watching! Also, if you are in the market for any tools, check out our Amazon store front. Visit our amazon store front for our recommendations for tools and supplies for DIY success! https://www.amazon.com/shop/housebarons If you click on any of the listed Amazon links there or in this description and buy, you are helping us out as a channel. We are Amazon affiliates and can earn from qualifying purchases and no extra cost for you. Thanks for the help in supporting our channel and enabling us to keep us making videos! #mailboxpost #removepost