• ClipSaver
ClipSaver
Русские видео
  • Смешные видео
  • Приколы
  • Обзоры
  • Новости
  • Тесты
  • Спорт
  • Любовь
  • Музыка
  • Разное
Сейчас в тренде
  • Фейгин лайф
  • Три кота
  • Самвел адамян
  • А4 ютуб
  • скачать бит
  • гитара с нуля
Иностранные видео
  • Funny Babies
  • Funny Sports
  • Funny Animals
  • Funny Pranks
  • Funny Magic
  • Funny Vines
  • Funny Virals
  • Funny K-Pop

Dab Pipe - making a dab straw скачать в хорошем качестве

Dab Pipe - making a dab straw 4 года назад

скачать видео

скачать mp3

скачать mp4

поделиться

телефон с камерой

телефон с видео

бесплатно

загрузить,

Не удается загрузить Youtube-плеер. Проверьте блокировку Youtube в вашей сети.
Повторяем попытку...
Dab Pipe - making a dab straw
  • Поделиться ВК
  • Поделиться в ОК
  •  
  •  


Скачать видео с ютуб по ссылке или смотреть без блокировок на сайте: Dab Pipe - making a dab straw в качестве 4k

У нас вы можете посмотреть бесплатно Dab Pipe - making a dab straw или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:

  • Информация по загрузке:

Скачать mp3 с ютуба отдельным файлом. Бесплатный рингтон Dab Pipe - making a dab straw в формате MP3:


Если кнопки скачивания не загрузились НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу страницы.
Спасибо за использование сервиса ClipSaver.ru



Dab Pipe - making a dab straw

Hey folks, thanks for checking out this video! There is no sound, so play your favorite music while you watch! In this video I make one of my signature style dab pipes. I make these with a small carb hole (2-3mm) in the wide part of the piece (not mouthpiece). Leaving the carb hole uncovered while using for dabs will allow fresh air to mix with the dab smoke, cooling it down and making for a smoother hit. This video is pretty straight forward, with a couple notable moves I’d like to describe: 0:30 I use my mini torch to heat my blowtube connection just enough for it to bend slightly. Using my rollers, gravity, and a little nudge with a rod, I then straighten my blank. At 5:00 I use my mini torch to blow a small bubble where I will open the mouthpiece. I don’t open it tat this time, just make a thin membrane so that it is easily opened later when I’ve made my carb hole and cannot put as much pressure into the piece. At 8:45 I do what I call the “assisted opening” when I pop the mouthpiece hole open. I use my trash rod and just touch the membrane of the hole I’m blowing out. This way, when I blow into it, the glass from the hole I just popped is collected by my trash rod rather than risk it sticking to the mouthpiece and leaving a scuzzy spot. It is hard to see in the video, but you can see me touch my rod to the end and then my flame moves as air comes out the hole. The membrane from the little bubble sticks to the rod rather than the surrounding area of my piece. At 10:15 I open the tip of the dab straw in the same way that some people open used blowtubes. I heat the extra glass on the end, fold it over with my jacks, and after a few seconds knock it off. The glass will break where the hot glass made contact with the cooler glass. If you did it right, there should be a very clean opening at the spot you chose. Thanks so much for watching this video! You can find my work on Instagram by following this link:   / dobbie_wan_glass   Please contact me there if you would like to inquire about purchasing glass, or just to say hello! I sell these dab pipes for $25 shipped, and usually have them in stock.

Comments

Контактный email для правообладателей: [email protected] © 2017 - 2025

Отказ от ответственности - Disclaimer Правообладателям - DMCA Условия использования сайта - TOS



Карта сайта 1 Карта сайта 2 Карта сайта 3 Карта сайта 4 Карта сайта 5