etrailer | Westin Sure-Grip Running Boards Installation - 2020 Chevrolet Colorado скачать в хорошем качестве

etrailer | Westin Sure-Grip Running Boards Installation - 2020 Chevrolet Colorado

Click for more info and reviews of this Westin Nerf Bars - Running Boards: https://www.etrailer.com/Nerf-Bars-~-... Check out some similar Nerf Bars - Running Boards options: https://www.etrailer.com/fitguidets.htm Search for other popular Chevrolet Colorado parts and accessories: https://www.etrailer.com/vehicle/2020... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-w... Shane: Hey guys, Shane here with etrailer.com. Today, I have a 2020 Chevrolet Colorado. And I want to walk through how to install the Westin Molded, Illuminated Custom Running Boards.Adding running boards like this to your vehicle is going to allow you to get in and out of your vehicle much easier. Not only for yourself, but also for your passengers. They're going to span from the front all the way to the back door. Each step is going to give you two lights, one in the front, one on the back. That'll help light up a step to give you that easy footing when you're getting in and out of the vehicle at night so you can see. We'll go ahead and shut the lights off and show you what it looks like. These are going to come on as soon as you open the door, because they're tied in with your dome light.Now, if you noticed that the lights we're kind of a yellowish color, they're very easy to change out if you wanted to switch them out for LEDs. These bulbs are going to be basically the same as your dome light bulbs, very easy to pull in and out. As far as the board goes itself, as I mentioned, it spans from in front of the front door, all the way to the back of the back door. The steps are going to be six inches wide. So they're plenty wide to get your foot on when you're getting in and out of the vehicle. We're going to have a raised back so it contours nicely with the vehicle, fits in very nicely. You're going to notice the grooves here, this is to help channel water away from your feet when the boards are wet.And when you compare these to other sets of running boards, except they have a plastic centerpiece, those plastic pieces can get a little slick when they get wet. With this, this is a polymer material, it's plastic but it almost seems like it has a textured rubber coating. Which is going to allow much better grip than a plastic. When you compare them to tube steps. Tube step again is just a bar that comes out and you have a plastic piece step here, and then one in the back. I think adding this on there really helps clean it up, gives it a nice finished look. Now you might be questioning the plastic material on the outside, the whole underside of it is going to be aluminum construction. So with the aluminum construction, we're not going to have to worry about rust and corrosion. And being aluminum, even though you might think that it's not durable enough, I'm 240 pounds and six foot, and it holds me up just fine. So plenty of durability with them, plenty of grip.We're going to do a test here, I'm going to go ahead and dump some water on them, and show you how much grip these have, even when they're wet. And you can see with the flex in it, I'm pushing on them pretty hard. So we got plenty of grip there. A lot better than those plastic ones. The polymer material is UV resistant, it's not going to crack or fade. These are going to be custom fit boards, they're going to come with the mounting brackets and hardware. They're also going to come with the wiring harnesses. The only things that it's not going to come with is your ring terminal, and also your connector for your power wire, or for your wire to tie this into the factory wire inside the vehicle. Now that we've gone over some of the features, let's walk you through how to get it installed.To start our installation we're going to start on the driver's side. We need to come to the inside, under panel of the vehicle, and we need to locate our mounting holes. We're going to be using these two on the very front, these right here in the center, and then the very back ones. So if you have rubber plugs in these, you need to make sure you remove those. You're going to have clips that look like this, we need to install those into the holes. We're going to go in the large hole, lining up with the small hole. Do the same thing for this bottom one, like that. We'll do the same thing for our four remaining holes.You're going to have six brackets, look like this, you want the front two on each side of the vehicle, this flange to face towards the back. So this one and your center one, this flange is going to face back. The very back one, this flange is going to be facing towards the front. Hex bolt, lock washer, and flat washer, we're going to line it up with the clips we just installed. And we're going to install the h