TTE710/810 Turbo DIY Install | Audi S4 B9 Stage 3 | Hybrid Turbo Upgrade скачать в хорошем качестве

TTE710/810 Turbo DIY Install | Audi S4 B9 Stage 3 | Hybrid Turbo Upgrade

This step-by-step DIY installation of the TTE710 hybrid turbo will show you how I transformed my 2018 Audi B9 S4 into an absolute monster. If you're considering a hybrid turbo, especially The Turbo Engineers TTE810 or 710, you should check out 034Motorsport's Dynamic+ Stage 3 ECU/TCU tuning. The power output and drivability of the car is absolutely fantastic, switch to E85 and it's a rocket ship. I will also show you an upper and lower PCV hose service. The lower PCV hose does require removal of the turbo, so this is an opportune time to swap it out. You will likely need other supporting mods to install this turbo, make a plan with your tuner! TTE 710 Turbo - https://bit.ly/tte710turbo TTE 810 Turbo - https://bit.ly/tte810turbo TTE 4-Bar MAP Sensors - https://bit.ly/4barmapforb9 034 B9/B9.5 Dynamic+ Tuning - https://bit.ly/034DynamicEA839 034 SuperDuper Inlet - https://bit.ly/superduberb9 Funk B9 Turbo Blanket - https://bit.ly/funkb9blanket Liqui Moly Pro-Line Additive - https://bit.ly/prolineadditive Turbo Manifold Clamp 059253139D - https://bit.ly/b9turboclamp Turbo to Manifold Gasket 059253232C - https://bit.ly/b9turboclampgskt Manifold Exhaust Gasket 06M253039G (2x) - https://bit.ly/b9turbomanigskt Turbo to Catalyst Gasket 8W0253115G - https://bit.ly/b9turbocatgskt M6x18 Torx Bolt N10196103 (4x) - https://bit.ly/m6x18 M6x12 Torx Bolt N10335206 (4x) - https://bit.ly/m6x12 Turbo Line Green O-Ring WHT007689 (3x) - https://bit.ly/b9turbooring Lower PCV Hose 06M103217DD - https://bit.ly/b9pcvhose1 Upper PCV Hose 06M129041 - https://bit.ly/b9pcvhose2 Thermo-Tec 3' Heat Shield - https://amzn.to/3MQF6lF Capri Tools Stubby Triple Square Bits - https://amzn.to/3E2OL3N GEARWRENCH Half Moon Wrench Set - https://amzn.to/42cvpCE Sunex 9726 Mini Ratchet & Bits - https://amzn.to/3m1V5CX VIM Tools Half-Cut Torx Bits - https://amzn.to/3MvbQ2j AEJ Metric Hex/Allen Bit Set - https://amzn.to/3MgIC8P Low Profile Offset Torx Drivers - https://amzn.to/4159bSR TEKTON 3/8" x 7/8" Offset O2 Socket - https://amzn.to/3MHkwV8 TEKTON Angled Tip Pry Bars - https://amzn.to/43x0na8 As an Amazon Associate and ECS Tuning Affiliate I earn from qualifying purchases. You don't have to purchase the specific items I'm linking to in order to help the channel at no added cost to you! 00:00 Introduction 00:14 Intake Air Box Removal 01:00 Turbo O2 Sensor Removal 01:31 Turbo V-Band Removal 01:45 Loosen Wiring Harnesses 01:58 Upper PCV Hose Removal 02:29 Turbo Inlet Removal 02:46 Unplugging Lower PCV Hose From Turbo 03:06 Support DG 03:27 Disconnect Charge Pipe From Turbo Outlet 03:55 Disconnecting Turbo Oil & Coolant Lines 04:29 Wastegate Actuator Removal 04:47 Vaccum Line & Diverter Valve Disconnect 05:09 Stock Turbo Removal 06:31 Lower PCV Hose Replacement 07:15 Prepping The TTE 710 Turbo 08:53 4-Bar MAP Sensor Installation 09:51 Turbo Line O-Ring Replacement 10:15 TTE 710 Turbo Installation 11:45 Turbo V-Band Installation 12:28 Final Turbo Reassembly 13:32 Charge Pipe Turbo Outlet Connection 13:58 034 SuperDuper Inlet Installation 14:32 Lower PCV Hose to Inlet Connection 15:13 Upper PCV Hose Installation 15:22 Intake Air Box Installation 15:42 First Start & Drive TTE 710 Turbo 16:23 Final Thoughts #theturboengineers #tte710 #034motorsport #hybridturbo #turbo