ENGINE VIBRATION - FUEL INJECTORS cleaning - 160 tkm SERVICE - BMW F20 engine N13 скачать в хорошем качестве

ENGINE VIBRATION - FUEL INJECTORS cleaning - 160 tkm SERVICE - BMW F20 engine N13

#EngineVibration #FuelInjectorsClean #RoughIdling #IntakeManifold #IntakePlenum #160tkmService #BMWF20 #BMWN13 BMW N13 engine problems and repair: 1. Vibration! You need to check fuel injectors and clean them in case of necessity. 2. Rough idling! This problem is caused by idling valve and throttle flap: You only need to clean them in order to avoid such problem. 00:00 ENGINE VIBRATION - FUEL INJECTORS cleaning - 160 tkm SERVICE - BMW F20 engine N13 00:35 Intake manifold - Remove from the engine 06:18 Remove fuel pressure line and fuel rail with fuel injectors 09:48 Cleaning Fuel injectors and using service kit for injectors 17:58 Install fuel injectors and rail back to the engine 21:42 Intake plenum and throttle body - Replace gaskets and install back to the engine 24:11 Install new Intake vanos solenoid valve 25:32 Intake plenum - Install back to the engine As in the previous episodes, I do a 160 tkm service for my BMW F20 car Let's continue where we left off in the last episode! The car currently consumes about one liter of oil per 1000 kilometers It seems that the valve stem seals are worn and need to be replaced In addition, one of the type defects of the N13 engine is the contamination of the tips of the fuel nozzles, which causes extra engine vibration Vibration, you need to check fuel injectors and clean them in case of necessity Rough idling, you only need to clean idling valve and throttle flap in order to avoid such problem Let's clean the tips of the fuel injectors while changing the valve stem seals The gasket at the bottom of the sound insulation of the upper part of the bulkhead must not be damaged Remove the DME and its holder Since I'm also replacing the valve stem rubbers, I make room for removing the valve cover at this point Remove charge air duct Remove intake manifold. Remember the hidden bolt (5 bolts in total) Remove pressure line. Loosen the lower nut first. Fuel escapes when fuel lines are detached. Unlock locks (1) and pull off cable channel (2) from rail Detach rail from cylinder head and remove Unlock and pull off connectors from injectors Next, the fuel injectors are cleaned and new seals and hold-down devices are replaced Remove decoupling elements from injectors Remove the fuel injectors from the rail Remove the hold-down device from the fuel injector Remove sealing rings and support rings Remove sealing rings, support rings, hold-down devices and teflon sealing rings Clean the nozzles of the fuel injectors so that the small holes are clean In some of the nozzles, those holes were partially blocked Install the new parts on the fuel injectors Slide new Teflon sealing ring on the place with using the tip of the pen as a guide Insert new hold-down device Put the fuel injectors back to fuel rail Place the fuel rail back on the cylinder head Make sure guide pin (3) of fuel injector is correctly positioned in designated hole in cylinder head (4) Install pressure line Next, intake plenum and throttle body Remove the old intake Vanos solenoid valve and install a new one I also changed the Vanos solenoid valve on the exhaust side without a camera Set of sealing and fastening parts for fuel injectors In the next episode, Valve stem seals will be replaced Let’s continue with the next episode! Stay tuned! Parts needed for fuel injector cleaning: BOSCH Fuel Injector Sealing Set 4 x Part: 13647600869 Intake manifold gasket set 4 x Part: 11617528340 throttle body gasket 1 x Part: 11617528341 And new vanos solenoid valves 2 x Part: 11368610388 -- Watch this video! If you liked this video, press the LIKE BUTTON, SUBSCRIBE channel, leave COMMENTS and SHARE video! By doing so, you will be able to support this Youtube-channel! Thank you! I appreciate it! 👍 Watch my previous videos on Youtube related to the maintenance and diagnose of BMW F20 with engine N13! See the whole series from here:    • BMW F20 - Diagnosis and maintanence   -- My purpose is to encourage people to do things themselves! Plus, this is a nice hobby for myself and at the same time I have the opportunity to save a lot of money by doing all the maintenance myself! I’m not a professional with cars or motorcycles, I just want to learn how to do things myself. If you do this service yourself, always check the correct instructions in the official service manuals. This is just my way of doing it! Jani Voutilainen You can follow me also in: INSTAGRAM:   / voutilainenjani   FACEBOOK:   / jani.voutilainen   YOUTUBE:    / janivoutilainen   Thanks for Music: Immersion by Numall Fix |   / numall-fix   Music promoted by https://www.free-stock-music.com Creative Commons Attribution-ShareAlike 3.0 Unported https://creativecommons.org/licenses/...