etrailer | The Low-Down on the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector скачать в хорошем качестве

etrailer | The Low-Down on the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector

Click for more info and reviews of this Optronics Trailer Lights: https://www.etrailer.com/Trailer-Ligh... Check out some similar Trailer Lights options: https://www.etrailer.com/dept-pg-Trai... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-o... Today on our trailer, we're going to be installing the Optronics Oval LED Trailer Clearance and Side Marker Light in the amber color, part number MCL31AB. We're going to first need to remove this old light. It doesn't work any longer. We're going to go ahead and use a flathead screw driver to remove the old lens on this light. Then this light here is actually riveted to our trail. We're going to drill out this rivet here and this rivet right here. Now, we've already cut the wire on the inside so we can go ahead and pull the light on out. Now, with the old light removed, we need to finish removing these two rivets. Here's our new light that we're going to be installing. It has a white wire for the ground and black wire for the power wire that we'll be tying in with the running light circuit on this trailer. We need to remove the lens to install the light or just take a flathead screwdriver and slip it right here in the groove and the lens come of. Now, we're going to go ahead and actually run both of our wires into the trailer here. We're going to go ahead and cut this ring terminal off for now. We're going to add a new one once we get the wires back inside. Depending on your exact application, you could coil them up and go to where you're going to use a mounting screw and put it through the front side here, and then go to mount it that way, or we're going to tie it inside instead. We're going to go ahead and snip this end off, go ahead and take our light here. You can see our two holes are lined up. Go ahead and get our mark with our drill. Screwed up just a little bit, we're going to ahead and drill a hole through the trailer. It will allow us to pull the two wires into the trailer. Now, we're going to go ahead and wrap the back wires here, which is a little bit of electrical tape right here just to protect it as it goes through our hole here. Now, we'll go ahead and take the two wires, feed them through the hole. Now, we'll go ahead and line up our two mounting location holes and we're going to install our new light with a couple of self-tapping screws instead of pop rivets. You can reuse pop rivets if you want to but we're going to go ahead and use a few self-tapping screws. Now that we got them started with our drill, we'll go ahead and tighten them the rest of their way down with our socket. Our lights, nice and tight to the trailer, go ahead and put the cover back on. Now, we're done here on the outside. Now, all that's left to do is hook up the wires on the inside of the trailer. We're going to go ahead and take our black wire and tie it with our running light circuit here on the trailer. We're just going to be using a butt connector to do this. We'll go ahead and trim it down a little bit as we don't need it so long. We'll then strip some wire back. We're going to take our wire and put it in the butt connector here. Then go ahead and crimp our butt connector down. Next, we'll add a little bit of electrical tape just to give that connection a little bit of protection. We'll take our white wire here, strip that one back a little bit. I'll go ahead and put a ring terminal on this end. Now, go ahead and crimp it down. Now, we'll go ahead and take our self-tapping screw. We'll put it through our ring terminal, and then we'll go ahead and tighten it down. With that, we're ready to go ahead and test out our light. We've gone ahead and turned off the lights so you can get a better idea of what this light will look like at nighttime. Now, we'll go ahead and turn on our new Side Marker Clearance Light. That's all there is to it to installing the Optronics Oval LED Trailer Clearance and Side Marker Light in the amber color, part number MCL31AB. .