etrailer | All You Need to Know About the 12V RV LED Puck Light скачать в хорошем качестве

etrailer | All You Need to Know About the 12V RV LED Puck Light

Click for more info and reviews of this Command Electronics RV Interior Lights: https://www.etrailer.com/RV-Interior-... Check out some similar RV Interior Lights options: https://www.etrailer.com/dept-pg-RV_I... Click for more info and reviews of this Command Electronics RV Interior Lights: https://www.etrailer.com/RV-Interior-... Check out some similar RV Interior Lights options: https://www.etrailer.com/dept-pg-RV_I... Click for more info and reviews of this Command Electronics RV Interior Lights: https://www.etrailer.com/RV-Interior-... Check out some similar RV Interior Lights options: https://www.etrailer.com/dept-pg-RV_I... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-review-co... Speaker 1: Today we're going to be taking a look at the LED RV Interior Light with Six Diodes. It's available in white with a switch. It's also available in white without a switch. It's also available in a black housing. This surface mount light is going to be great for your ceiling or underneath your cabinets in your RV, camper or fifth wheel trailer. It's also ideal to use in those bunk bed areas of your RV or camper where there's little to no headroom. Since it is LED, it's going to be brighter. It's more efficient, and there are no bulbs to replace. Another great thing about LEDs is there much safer than traditional bulbs, and they're not hot to the touch. The six diodes are going to provide 204 lumens, so they'll be great for those small areas in your RV or camper.If you picked up the one with the switch, it's located right here in the center, and it's an easy operation. Some RV or campers have a separate switch, so you may opt for the one without the button which will give you a cleaner look. It's three inches in diameter and 1/2 inch deep. It simply wires into your RV or camper's new or existing 12-volt system.I'll go ahead and show you how to get it installed. I'm in the bottom bunk of my travel trailer. I've already gone ahead and removed my single dome light. It was large and bulky. I'd like something a little bit more low profile and easy, so I'm going to be installing this low profile light here. I pulled my wires through. Our old wiring used some wire nuts so we're just going to go ahead and reuse these, and since we're hooking up an LED light, it doesn't rightly matter which wire goes to where. We're going to go ahead and do white to white, so we'll take both of our white wires here. We'll put them all together, and then we'll go ahead and screw on that wire nut. Make sure it's nice and tight and give it a good pull. Make sure they're not coming out. Then we'll just repeat the same process with the brown and black wires. Perfect. Now we can turn on our power and check it out. I'd say it works great.Now, let's finish up our install. In order to mount the light to the ceiling, we'll need to remove the lens. We can just take a screwdriver and pop it out just like that. From here, we'll just tuck our wiring back up into the ceiling like so. As you can see, I've got a series of holes from my previous light. I'm going to try to hide those as much as I can, and I'm going to use my existing hardware from my other light. If you're going to be using your hardware from your old light, you do want to be sure that it's low profile. That way when you go to put your lens back on, it'll fit right over them. Most of the hardware used in your RV or camper is pretty thick and bulky. You want to be sure when you use this light you switch to a low profile hardware. That way you can get your cover back in place. Perfect.That's going to complete our look at the LED RV Interior Light with Six Diodes.