Adding a High-Tensile Hot Wire to an Existing Barbed Wire Fence (Offset Installation) скачать в хорошем качестве

Adding a High-Tensile Hot Wire to an Existing Barbed Wire Fence (Offset Installation)

In this video, we show how to add a single high-tensile electric offset wire to an existing barbed wire fence. This is a practical way to carry power down a fence line while also extending the life of older barbed wire infrastructure. In this case, the existing fence is still structurally sound, but we plan to replace it with a purpose-built high-tensile electric fence in the future. For now, we’re using the barbed wire fence to accomplish two goals: Carry electricity down the fence line to feed additional fencing. Reduce livestock pressure on the old fence by adding a hot wire. Once the fence is electrified, cattle stop pushing, rubbing, and reaching through the barbed wire. That alone can add several years of life to an aging fence. Why Use an Offset Wire? Running an offset hot wire on standoff insulators allows you to: Feed electricity thousands of feet along existing fence Tie into new high-tensile fence builds further down the line Improve livestock respect for older fences Avoid electrifying the barbed wire itself (which can be dangerous) Electrified barbed wire can pose serious risks if animals become entangled, so keeping the hot wire properly offset is critical. Tools & Materials Used We demonstrate: A pre-made ratchet strainer and insulated cable assembly Screw-in insulators for corners and high-tension locations Standoff insulators for straight runs Drill-mounted insulator tool Proper staple technique to prevent rotation Warning sign installation using a wire clamp trick The pre-made ratchet strainer assembly is more expensive than tying wire off manually, but it’s quick, clean, insulated, and easy to remove later. This makes it ideal for temporary or transitional installations like this one. Installation Highlights Running the Wire First We pull the high-tensile wire down the full length before installing insulators. This allows proper slack control and safe cutting. Corner Installation At outside corners, we use heavy-duty screw-in insulators instead of lightweight standoffs. These handle directional pull much better and prevent strain on plastic components. Standoff Insulators on Line Posts On straight runs, we use standoff insulators spaced at reasonable intervals (not necessarily every post). The goal is to: Keep the hot wire well away from barbed wire Prevent tangling or shorting Avoid electrifying the barbed wire Installing standoffs sideways first makes wire insertion easier under tension. Once the wire is in place, rotating them upright and stapling over the vertical spike locks them securely. Tensioning the Wire Because this is not a purpose-built high-tensile system, we do not tension the wire as tightly as we would on a new electric fence. We remove slack while avoiding unnecessary strain on older braces and corners. Safety Considerations Keep the hot wire far enough from barbed wire to prevent accidental electrification. Install warning signs near gates and high-traffic areas. Secure warning signs so they don’t slide or blow in the wind. Avoid creating conditions where animals could become entangled in energized barbed wire. The Result We now have: A clean offset hot wire Power carried down to the next brace and future fence Reduced livestock pressure on the existing fence Extended life for aging barbed wire infrastructure This approach is an effective transitional strategy while planning for a full high-tensile electric fence upgrade. Related Videos Building High-Tensile Electric Fence Sizing Your Energizer & Ground System Common Faults in Permanent Electric Fence Fault Finding & Fence Testing Tools If you're working with existing barbed wire but transitioning toward high-tensile electric systems, this method can save time, reduce wear, and improve livestock control in the meantime. Related Videos in This Series How to Test and Size Your Energizer and Grounding System    • How to Install a Proper Grounding System f...   Common Faults in Permanent High-Tensile Electric Fence    • Common Faults in Permanent High-Tensile El...   High Tensile Electric Fence Layout & Design    • High Tensile Electric Fence Layout & Design   For more, check out our: Rotational Grazing Playlist    • Rotational Grazing   Electric Fencing Playlist    • Electric Fencing   Subscribe for more fencing and grazing education: https://www.youtube.com/c/SmallScaleM...