У нас вы можете посмотреть бесплатно 18) Testa di violino parte diciottesima - Sgrossatura della cassetta piroli или скачать в максимальном доступном качестве, видео которое было загружено на ютуб. Для загрузки выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием видео, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса ClipSaver.ru
INDICE DEI VIDEO : http://davidesora.altervista.org/vide... ENGLISH TRANSLATION of the written notes in the video, in order of appearance : 00:04 - Violin scroll part eighteen - Roughing of the inside of the peg box 00:15 - Before start digging refine the lines of the pegbox using some fine cut oval files, the knife and the flat scraper 00:28 - Connect harmonically the narrowing from the maximum width of the box to the nut, preserving the marks of the neck lines 01:56 - Finish the throat harmonizing the lines with the curves of the back and of the volute 02:48 - Clean the surface definitively removing all marks of the compass and the remaining scratches 03:04 - Make sure that the throat space gradually open outward without narrowing 03:14 - Keep concave the pegbox line in correspondence with the the volute, changing the direction of the curve together with the line of the back 03:26 - Mark the thickness of the upper part of the jaws (5 mm) 03:56 - Draw the end of the pegbox using the volute as a guide 04:04 - Make sure of the symmetry of jaws with respect to the center line at the nut 04:22 - Put the scroll in the vice making sure it is parallel to the plane of the bench, to have a safe and intuitive reference of verticality 04:33 - Use a drill of 5 mm in diameter, marking with tape the maximum depth for roughing, which must not exceed the lower level of the holes for the pegs 04:50 - Tilt well the drill for the first two holes, heading directly toward the G peg to keep a well inclined wall at the nut 05:14 - Always tilt the drill also towards the outside, in order to respect the increase in thickness of the walls at the box bottom (7 mm) 05:30 - Start drilling perpendicularly making a guide hole 05:37 - Tilt outward 05:52 - Perpendicular guide hole 05:57 - Tilt outward 06:07 - For holes at the end of the box dig with a gouge obtaining a plane to drill perpendicularly without slide the drill bit 06:44 - Use extreme care not to damage the volute touching it with the drill bit 06:56 - Start roughing with a flat and wide gouge cutting the links between holes 07:18 - Use a narrow gouge and very curved to eliminate more easily the excess wood 07:35 - Continue with the 22 mm chisel 08:22 - Switch to the 6 mm chisel instead of the gouge to finish the digging coming inside corners 08:36 - Isolate the entire surface of jaws to highlight the line well and prevent chipping 09:18 - Always cut strongly angled in order to respect the increase of the thickness of the walls at the bottom of the box (5 mm above, 7 mm at the bottom) 10:39 - Cut accurately the corners at the end of the box, isolating the surface of jaws to avoid tearing it accidentally 11:01 - Cut along the fiber split creating a plane to facilitate the subsequent working and determine the line of the end of the box 11:47 - Use a long-bladed knife to cut into corners unreachable with chisels and for incise the base of the walls 12:18 - Cut the terminal endgrain wall taking care to respect the inclination of the side walls 12:37 - With the 6 mm chisel cut the bottom of the box bringing it to about 3 mm below the holes for the pegs, following the curve of the back as a reference 12:55 - Trim the endgrain wall at the nut defining well the corners, leaving it though still abundant to protect the gluing surface of the nut 13:41 - With a 10 mm chisel cut the bottom underneath the G peg in the opposite direction, cutting well the sides and paying attention to the fiber split 14:01 - Check that the thickness of the bottom is close to the definitive measure but still slightly abundant (about 5.5 / 6.0 mm) 14:21 - Finish the thickness at the bottom of the walls, leaving it still abundant of about half a millimeter 15:01 - Index of videos : http://davidesora.altervista.org/vide... 15:08 - http://www.davidesora.it/ .