How to Manual Swap an Automatic Toyota MR2 SW20 (1991-1995) | Part 2 of 3 скачать в хорошем качестве

How to Manual Swap an Automatic Toyota MR2 SW20 (1991-1995) | Part 2 of 3

This is part 2 of a three-part guide on how to manual swap an automatic 1991-1995 Toyota MR2 SW20. My 1991 Toyota MR2 is equipped with the 5S-FE engine and had the A241E automatic transmission but now after doing the swap it has an S54 transmission off of a 91 non-turbo Toyota MR2. In this video I show how to install the clutch lines, replace the automatic brake pedal to a manual brake pedal, install the clutch master cylinder, and install the clutch pedal. Here is the link for part 1 that goes over the majority of parts needed to do the swap and how to replace the automatic shifter assembly and shifter cable to the manual shifter assembly and shifter cables. How to Manual Swap an Automatic Toyota MR2 SW20 (1991-1995) | Part 1 of 3    • How to Manual Swap an Automatic Toyota MR2...   I'd like to note that I already had the automatic transmission removed due to removing the engine and transmission to perform a refresh on my engine. You don't have to remove the engine and transmission together to remove the transmission, you can leave the engine supported with an engine support bar and remove the transmission by itself. If you'd like to remove the engine and transmission together to perform work on your engine like I did, I'll link my videos down below on how to remove them. The videos could also serve as a guide even if you're just removing the transmission by itself so feel free to check them out. Step-by-Step Guide: How to Remove the Engine & Transmission from a 1991-1995 Toyota MR2 (Part 1/2)    • Step-by-Step Guide: How to Remove the Engi...   Step-by-Step Guide: How to Remove the Engine & Transmission from a 1991-1995 Toyota MR2 (Part 2/2)    • Step-by-Step Guide: How to Remove the Engi...   Parts list - (the parts listed below are the parts that were mentioned in this video, due to the limitation of 5000 characters in a YouTube description the rest of the parts needed for the swap will be in the description of part 1and 3.) Clutch line that goes from clutch master cylinder to union - 31481-17080 (discontinued) so get used or a stainless steel braided hardline from Prime MR2 that replaced both clutch lines and union Clutch line union - 90412-12034 Clutch line that goes from union, runs underneath vehicle and makes its way towards rear of vehicle - 31489-17020 (discontinued) so get used or a stainless steel braided hardline from Prime MR2 that replaces both clutch lines and union. Manual brake pedal - get used Clutch pedal - get used or a new one from MR2 Heaven Clutch master cylinder - 31410-17100 (discontinued) however lots of aftermarket options, I can't recommend one since I used a used OEM one. Pin for clutch master cylinder 90240-08071 Clip for pin for clutch master cylinder 90468-16142 M8x1.25 nuts x2 for clutch pedal and clutch master cylinder M8x1.25 bolt short in length for clutch pedal Spring for clutch pedal 90507-14002 (discontinued) so get used or MR2 Heaven offers a spring that potentially could work Clip that holds clutch hose - 90468-08035 Clutch hose 90947-02611 Chapters: 0:00 Intro 0:42 Clutch line 31481-17080 installation 6:59 Automatic brake pedal removal 10:52 Finalizing Clutch line 31481-17080 installation 13:52 Manual brake pedal installation 16:28 Clutch pedal and clutch master cylinder installation 20:43 Clutch line 31489-17020 installation 34:19 Clutch line union 90412-12034 installation