✅ Multiprotocol TX Module for FrSky Taranis Turnigy 9XR NRF24L01 Eachine e010 скачать в хорошем качестве

✅ Multiprotocol TX Module for FrSky Taranis Turnigy 9XR NRF24L01 Eachine e010

Multiprotocol TX Module http://bit.ly/bgmultitxproto This simple inexpensive single chip multi protocol TX module works with transmitters with PPM and channel orders of AETR. It can speak a handful of protocols used by the NRF24 RF chip. It's not as feature rich as the 4in1 multi-module but it works great if your model is supported for a fraction of the cost. Manual: http://img.banggood.com/file/products... Goebish firmware https://github.com/goebish/nrf24_mult... Eachine E010 Mini 2.4G 4CH 6 Axis Headless Mode RC Quadcopter RTF http://bit.ly/bgeachinee010 FrSky Taranis Q X7 http://bit.ly/bgtaranisqx7 http://bit.ly/bgx7s http://www.gearbest.com/multi-rotor-p... FrSky Taranis X9D+ http://bit.ly/bgtranisx9dplus http://amzn.to/2pMp5Ul http://www.gearbest.com/rc-quadcopter... ----------------- Binding Procedure ----------------- 1. Create a model in OpenTX using external module in PPM mode, 12 channels and AETR sequence order 2. Turn off Taranis 3. Power up quad 4. While holding the appropriate stick pattern listed below, power up Taranis. ----------------- Selecting Protocol Protocol is selected with stick position at startup Last used protocol is automatically selected if stick is in neutral position ----------------- Rudder right + Aileron right + Elevator down = EAchine E010, NiHui NH-010, JJRC H36 mini Rudder right + Aileron right + Elevator up = FQ-777-124 Pocket Drone Rudder right + Aileron left + Elevator up = CX-10 older red PCB/CX11/CX205/CX30, JXD389/391/393, SH6057/6043/6044/6046/6047, FY326Q7, WLToys v252 Pro/v343, XinXun X28/X30/X33/X39/X40 Rudder right + Aileron left + Elevator down = WLToys V930/931/939/966/977/988 Rudder right + Elevator down = HiSky RXs, HFP80, HCP80/100, FBL70/80/90/100, FF120, HMX120, WLToys v933/944/955 Rudder right + Elevator up = Syma X5C (older model), X2 ... Rudder right + Aileron right = MJX X600 Rudder right + Aileron left = EAchine H8 mini 3D, JJRC H20/H22 Elevator down + Aileron left = Syma X5C-1/X11/X11C/X12 Elevator down + Aileron right = Attop YD-822/YD-829/YD-829C ... Elevator up + Aileron right = EAchine H8(C) mini, BayangToys X6/X7/X9, JJRC JJ850, Floureon H101 ... Elevator up + Aileron left = EAchine H7 Elevator up = WLToys V202/252/272, JXD 385/388, JJRC H6C, Yizhan Tarantula X6 ... Elevator down = EAchine CG023/CG031/3D X4 Aileron left = Cheerson CX-10 green pcb Aileron right = Cheerson CX-10 blue pcb & some newer red pcb, CX-10A, CX-10C, CX11, CX12, Floureon FX10, JJRC DHD D1 ----------------- Extra features (if available on aircraft) ----------------- Channel 5: led light, 3 pos. rate on CX-10 and FQ777-124, H7, inverted flight on H101 Channel 6: flip control Channel 7: still camera Channel 8: video camera, pitch trim (FQ777-124) Channel 9: headless Channel 10: calibrate Y (V2x2), pitch trim (H7), RTH (H8 mini/H20, FQ777-124), 360deg flip mode (H8 mini 3D/H22) Channel 11: calibrate X (V2x2), roll trim (H7,FQ777-124) Channel 12: Reset / Rebind